Antonovka
I have a small and also waste with a tablespoon
gawala
Quote: Antonovka
waste with a tablespoon
In general, for me this is not the kind of waste to fool myself ..
Antonovka
gawala,
Yes, I don't bother either - I just add it to the bread and that's it
Olga VB
Quote: gawala

How many? Is your elephant big or small?
I also had a lot left until I thought to poke at the + button. and scroll for another 3 minutes leftovers. There is practically no test now. What is in the matrix and literally a teaspoon in the hopper.
Large.
my bunker is empty, but the matrix is ​​full. A little more crawls out of its limits.
I finish it by hand, I do not like to shove pieces on the refrigerator.
gawala
Quote: Olga VB
on the matrix is ​​clogged. ...
Well, the matrix should be crammed, no one promised a pure matrix ..
Olga VB
Quote: gawala
nobody promised a pure matrix ..
hachuuuuu
gawala
Quote: Olga VB
hachuuuuu
What for? It's so interesting to scrape the rest of the dough out of the matrix .. How to play plasticine ..
Anna67
gawala, I usually wait until it dries up and meditatively knock it out for cleaning. Enrages much less than a garlic press or a fine grater with a scratchy surface.
gawala
Quote: Anna67
Enrages much less
Nothing pisses me off at all. Right there, while the mass is warm, I picked it up with a knife and that's it .. But it's soft, so pleasant. while you dig out, you will play enough ..
Anna67
gawala, even a grater? If I don’t rip my hands off her, then this is three out of ten times.
I'm going to make pasta. Today I took apart the cabinet and found two open packages of durum, threw one out with the can - the creatures started up again (it was not a year and a half, I was already bored), the second one seemed to be sifted, but it’s still scary, all the flour is in one cabinet ...
gawala
Quote: Anna67
even a grater? If I don’t rip my hands off her, then this is three out of ten times.
Even a grater .. I always remember that I have it sharp .. so I observe safety precautions.
Quote: Anna67
threw it away with the can
What a pity .. Can you heat the flour in the oven?
Irlarsen
I returned the elephant. Today, in a calm state, I tried again and realized that he just had a defective motor. Not enough power. He stops, begins to hum, and the pasta does not come out. I paused, took out the crumb and began to put it in small parts, that's when everything went fine. But I don't need such a device

Thanks again to everyone! I'll live without an elephant
gawala
Quote: Irlarsen
It stops, it starts to hum
It does not have to stop, it runs continuously for the entire programmed time. It mixes for 3 minutes, then a pause for a few seconds and then the spaghetti auger starts to work.

Quote: Irlarsen
I don't need such a device
Quite right.
julia_bb
Quote: Irlarsen
I returned the elephant. Today, in a calm state, I tried again and realized that he just had a defective motor. Not enough power. He stops, begins to hum, and the pasta does not come out.
That's it, but we can't understand anything, why it doesn't work out.
Yes, to return this immediately, that's right.
ladybu
Girls, good afternoon. Tell me, who uses a 200W and 150W pasta machine, is the difference noticeable? I want my sister to order a pasta machine for Alliexpress as a gift. But they all have a power of 150W. Is this small or normal?

gawala
Quote: ladybu
It is not enough
Works slower. 18 minutes the whole process goes. I looked at the official website it says.
katyaspb
The girls who made the horns for the little elephant don't fall apart? When drying (just on the table), they fall apart lengthwise into 3 parts
Made from solid Italian flour.
kseniya D
Catherine, I did, but did not dry. I cooked it right away, nothing fell apart. made with the addition of flour / s, about 20%.
Sofita
On the first day I made purchases from premium flour Makfa, which was at hand in a small machine, macaros with holes and immediately cooked the normal ones. Most of all I like to make spaghetti from durum flour




From flour durum from vila taste 50% and 50% Makfa premium




I didn’t like 70% of durums and Makfa, 30%, I didn’t like it very much, it crawled out worse, too.
katyaspb
kseniya D, Ksenia, when cooking fresh, everything is in order too, but they dried up and fell apart at the seams. Now I'll try them on plain flour, it looks like the seams from the 'durum' don't stick well together.
Sofita, for some reason, I also like it better when there is less solid flour, I'm not Italian
marinastom
Girls, I share my sadness and urge you not to repeat mine, I don't even know what to call what ...
On Wednesday I wanted to make spaghetti, I was in a hurry and did not look that there was a spatula in the mixing container for cutting pasta. I poured flour, turned it on for stirring and heard a terrible crack! I turned it off right away, but it was too late: one curved blade broke off, and the inner protrusion of the body near the shaft, it was simply ripped out ... I sobbed the same way ...
I ask for help: I ​​want to try to glue. Who will tell you what, the better? I bought a Cosmophen, or maybe an epoxy? Ask the masters about this in your environment, please!
I am very sorry for my assistant ...


Pasta machine Philips HR2355 / 09
Pasta machine Philips HR2355 / 09
Sorry, the photo turned out "on the side" ...






Remember a few pages ago you discussed a review from Ozone with the same breakdowns? I think there were suckers like me ...
Antonovka
marinastom,
Marin, I doubt that the glue will withstand and how much it is suitable for contact with food ((It's a pity, of course ((Maybe contact Philips service with a question about the possibility of buying
marinastom
Yes, Len, I thought about it too ...
I'll try to call or write on Monday. But it's hard to believe in success, and it's probably expensive ...
katyaspb
marinastom, I also think that gluing will be unreliable, but screw it up? The protrusion on the body, I think, is definitely possible.
marinastom
There, in the blades, there is a cavity inside, so I thought, maybe what kind of core should I put in and fill it with epoxy?
gawala
marinastom, Marina, what a pity. showed her husband, said that I had to buy a new spare part. It is useless to glue and you cannot insert the rod. The next blade will fly ..
katyaspb
The blade, like the gluing surface is not so small, if you still strengthen it from the inside, it can work out. ... After all, if the dough is the correct crumb, without a large lump, then the load on the blades is not the greatest
gawala
Well, in any case, you can try.
katyaspb
+100000
Need to try
marinastom
Girls, thanks for your support!
I will definitely try all the options.
And, yes, the most important thing will be the correct proportions of the dough ...
Antonovka
marinastom,
The husband said that Cosmophen in any case NO, it is ciaclerate, it is poison !!!




There is no epoxy either ((
marinastom
M-yeah ... And what? ..
gawala
Quote: marinastom
And why? ..
Nothing .. Call-write to Phillips .. There are no spare parts in German ibey. I already watched.
Annutka
marinastom, Marin, it seems to me that you can just contact the service, they also order spare parts. Straight upset ...
marinastom
On the Philips website, in the Support section, I found a phone number. Although it is written around the clock, I will call on Monday, most likely, now just the operator on duty, maybe during working hours more information can be obtained ...
But it's sooooo hard to believe ...
kil
Perhaps some kind of composite for dental crowns. It's certainly not poison.
marinastom
Damn! And I, a dentist, what am I thinking about? ..
Ira, thanks for the kick! I will make a stop at our orthopedists!
Svetlenki
Quote: gawala
Nothing .. Call-write to Phillips .. There are no spare parts in German ibey. I already watched.

I also had a glimpse of an English Amazon-ibey - no. I support the opinion that you need to call the service and find out. This part should not be too expensive.

marinastom, Marina, I will keep my fists! Be sure to report the result of the call to the service.
marinastom
Girls, thank you so much that I have you!
For three days I was tormented whether or not to write about my misfortune, and now I understand that it was not in vain that I wrote.
I will definitely knock everywhere and I will tell you everything whether it will work out or not!
Annutka
marinastom, Marina, we are waiting, we are experiencing!
Pchela maja
I really sympathize. And on a 3D printer, probably not an option to print a part? I wouldn't glue for sure.
And yes, contact the service. The main thing is that the part does not come out at the price of a new machine from Okey.
shade
Peace be with you bakers!

well glue it is not a problem

LOCTITE if you find, or even ordinary superglue only with salt
marinastom
How is it with salt? ..
Anatoly came and the riddles began ...
I just thought, we only need to look for a sleeve with blades, because the protrusion of the container can be glued, even with cyanoacrylate, there is gluing outside.




I don't even know where to look for a 3D printer ...
shade
Peace be with you bakers!
Carefully and as quickly as possible

It is advisable to sift or grind the salt, so that it would be straight very finely
Moistened - salted - applied
only it is necessary quickly, according to how much it grabs at the moment. of course you need to try on something before making a clean copy, I glued the bump stop in a dough sheeter - I keep twisting for a year

marinastom
So, mysterious you are ours, I understood correctly: first spread with glue, then sprinkle ashes salt, then squeeze the glued? Sprinkle on both sides? Will my cosmophen go? Loctite don't even know where to start looking? ..
shade
Peace be with you bakers!

Here salt acts as reinforcement,
I moistened the two halves with glue, sprinkled one with salt and pressed the other half, but I do not have a large gluing area, and if you need to glue more, then glue the ends without salt and then moisten the seam with glue and sprinkle with salt

you can watch on YouTube, there are several videos with experiments like this--

Olga VB
Marisha, honey, do not suffer!

🔗


Good luck!
marinastom
Olya, thank you very much !!!
I ordered, paid, I will wait with the Russian post ...
They seem to be working a little better.
Maybe, of course, somewhere else there would be, but, as they say, a tit in a hand ...




But I'll try to glue mine anyway ...
Anna67
Wow, well, and the prices - we can say a baby elephant with a discount at the price of spare parts and a motor as a gift. Who knows, I'll suddenly fall asleep with flour and turn it on without noticing ...
Twig
Spare parts are always expensive. 910r - I think in a godly way in general. Moreover, judging by the reviews on Ozone, it was this detail that broke down in people.
That is why we do not sell additional attachments?
Marina, don't even bother with sticking the blade. Let this be the biggest nuisance in your life. Well, for others, science and a reminder to be more careful.

All recipes

New recipe

© Mcooker: best recipes.

map of site

We advise you to read:

Selection and operation of bread makers