Furniture for kitchen

Anya, that's why I went broke that the studio and gas, the capacity there is 990, that's good !!

they mentioned the studio, is it possible there without a hood?

I mainly use it for lighting, but I have an electric stove. The noise annoys me. And I don’t cook fatty stuff at all - I’m sybarite. Now if there’s gas, I’ll have to.

ABOUT! I watched the video of the built-in Boshevsky hood - it's just incredibly quiet! Not too powerful, of course, but I compare this with mine. But mine makes a lot of noise.

For me, too, the hood only works with a lamp, it's even a pity that so much space is lost. But there, after all, nothing else can be attached, because all the same above the cooking room and space is needed, and the steam must go somewhere.

this is what the built-in hood looks like

[Anna1957]

Anna1957, the 45 cm hood is probably minimal, so that it captures everything just conveniently. The width of the plate plus 12 cm from the side. I had dominoes at my dacha, the pull-out hood is silent, but these are Miele-the quietest, now their prices are probably sky-high

[Anna1957]

Anna1957, the 45 cm hood is probably minimal, so that it captures everything just conveniently. The width of the plate plus 12 cm from the side. I had dominoes at my dacha, the pull-out hood is silent, but these are Miele-the quietest, now their prices are probably sky-high

Yes, probably.

this is what the built-in hood looks like

Is this your photo? Please show me your apron. I also want flowers.

[Irina]

Irina, already showed close)))

Girls and then I'll show you the kitchen, maybe someone will come in handy
My idea and color too)

the apron is tiled with decors

And the refrigerator, they reworked the opening to put it and it did not bother anyone

[Masinen]

Masinen, I have a kitchen of the same color, only the countertop is darker "root" (root). I like it very much, I go in and am happy!

[svetta]

svetta, honestly, I thought it would be cold from this color, but in the end it turned out super! right to the eye pleases)
BUT this is not my kitchen, I have Orange.

[tana33]

tana33, ahh, I was delighted then. Chet forgot.

[Irina]

Irina, if you want, I will send pictures from the site from which they were taken for photo printing

[Maria]

Maria, very cheerful and joyful color of the kitchen, I would definitely like it))))

And how is it more convenient and more rational to place the sockets: on the wall (like Masha's) or on the bottom surface of the wall cabinets?
Mash, and what quality facades? Can you show the corner? And the facade, and inside?

[Tatyana]

Tatyana, exactly)
it turned out well that it was possible to put the oven in a corner, but in my kitchen this could not be done, because the pipe goes through, it stands in the middle and cuts the work surface.

Mash, and what quality facades?

If I'm not mistaken, the film is matte and there are no prints left. when you touch the door, then how roughness is present.
This is an economy class.
There is such a color in gloss, very beautiful, but the price will already be higher.

[Anna1957]

Anna1957, if the outlet is at the top, then the radius of the device is limited, often the cords are short. And on the wall it gives more maneuverability, and the wire below does not interfere so much. IMHO

Economy class.

You don’t remember about the price - how is it measured there? Linear or square meters? I've forgotten everything

[Anna1957]

Anna1957, if the outlet is at the top, then the radius of the device is limited, often the cords are short. And on the wall it gives more maneuverability, and the wire below does not interfere so much. IMHO

I now have both options, but I have not yet decided how to do it in the new kitchen. It seems to me more convenient under the lockers, the length of the wires seems to be enough.

And how is it more convenient and rational to place the sockets: on the wall (like Masha's) or on the lower surface of the wall cabinets?

from my point of view, on the bottom surface of the cabinets is convenient only for temporary switching on
for example, a mixer, turned on, worked, turned off
if the device is stationary, then the wire will dangle from above and enrage me)))

therefore both options are needed)))

I have all the sockets on the side, there the equipment will stand
but I really want to make such a backlight with an outlet


while the price of the kit stops, and I don't need hooks, in general I think)))

[Anna]

Anna, so I don't remember. I count for the assembly by running meters. But I don't remember the facades)

Go to Leroy's website and see the price, it's from their store. Their prices change, so it's better to check on the website.

[Anna]

Anna, I have sockets on the wall in Moscow.
And in Bosnia, both on the wall and next to the illumination on the oblique, but there are no upper cabinets.
I can say that the more the better

the bigger, the better

It's clear

I had 6 sockets on the working wall in my apartment - not enough. The house has 3 blocks of sockets for 14 places - not enough! But there is not enough now because two blocks were closed by a microrail and a coffee machine and it became inconvenient to use sockets. Now I want to install the block of outlets vertically, maybe it will be more convenient.

this is what the built-in hood looks like

This is how it looks wrong built-in hood. ))) You cut her exit area by almost half, and even a square section. Plus, for sure turns ... In short, even if the exhaust shaft in the house is ideal, then the exhaust power drops with this treatment, well if by a third. ((

[Lena]

Lena, it was not us, the furniture makers, who built it in, what exactly is wrong? that the exhaust pipe is not round?
the pipe will be altered to the shaft, but it will still be rectangular, turn one, from the cabinet, then straight to the shaft

It seems to me that any average kitchen should have at least 2 such block of outlets, and on average - 3-4
These blocks are rectangular and long linear, they can be placed vertically, horizontally, up, down and sideways entrances. I'm very comfortable.

that the exhaust pipe is not round?

And not round, and narrow. ((The manufacturer provided for an exhaust with a cross section of 177 sq. Cm, but for you it was forcibly reduced to 100 (the pipe was added 10x10?)

But if you use the hood as it is more accepted here, that is, basically only light bulbs, then there will be no problems. The bulbs will shine properly.

I use the hood recklessly, I even cut onions in its area so that my eyes do not pinch.

Olga VB! And for the not very gifted, can I have a photo of these sockets? Six months later, repairs in a new building, the husband must be prepared in advance. While planning 2 blocks of 4 sockets on the long side of the table top and another block × 4 on the short side. I'm thinking, is it enough or not? Microwave and refrigerator do not count

[lira3003]

lira3003, so you go to its active link, I myself dream of such ...

Well, I chased two birds with one stone! I choose compression stockings, well, I look here .... I need to focus on one topic. Thank you Olga VB for the filter pictures! And Scarlett, thank you for helping me collect my eyes

And I have sockets that are very convenient to attach under the cabinets and there is nothing to do.
🔗

Horse price. Olginas are much cheaper.

It is the switches at each point that are valuable to me, since many devices are now turned on and off not by their own separate button, but by sticking and pulling the cord. I have such Kesha, princesses, multitrack, etc., etc.
It is very inconvenient, to pull the cords back and forth, and they get confused forever. And here everything is with individual switches.
Only, of course, such filters do not like a very heavy load, so I divided them into 2 different lines so that heavy loads do not fall on one. For example, I have princesses and a teapot on different lines.

Olga VB, what company and model are your "socket blocks"? And where can you buy them ???

This unit is an ordinary surge protector, only suspended on my wall (there are special mounts for this). And the lead wire is tucked away behind the cabinet.
My firm is Sven. They are different.

🔗

I chose the one with an additional master switch. I have a hood connected to this switch, that is, in fact, 6 sockets and + 7th point are used.
I bought for a long time, but he knows everything

My firm is Sven.

And I have such a firm, only nests in one row, lies near the wall. I also turn on one device at a time, I will not risk several at once. I don't connect the kettle to it, I have 2400 W, and the total load of the filter is up to 2200 W. I wanted to buy one more, found another company, more powerful, such
🔗
Now I think to buy or not, there are different nests, although all are useful.

I have a kettle from him, and princesses, and an iron. Of course, not simultaneously on the same line.
And the Bridge has other filters, with the same sockets.

🔗

Girls, hello.
I plan to buy my first kitchen in my life)
I read the whole topic. How many useful things !!! There are many things I would not even think about.
Thank you very much !!!
Well, of course, there are many questions.
And stupid ones too) I'll start with one of them)
I have a lot of plastic containers and we use them a lot.
So after PMM, they remain wet. Where to put them and where to dry them? Or do you always have to wipe it off before putting it away?
Now it's drying on the table, and I put it there. But in a new kitchen, this is impossible)

I wipe. Sometimes I put it in the sink. I have 2 bowls and one of them has a dryer, there is put something washed by hands and to dry.

Virgo, who had facades of different quality - share your thoughts on the optimal price-quality ratio. Resistance to damage, ease of cleaning, appearance, etc.

[Lisichkalal]

Lisichkalal, plastic in the dishwasher does not dry out unambiguously. I dry (finish drying) as usual dishes - on a towel near the sink. If you need it urgently - in the oven for blowing at a low temperature

I have a lot of plastic containers and we use them a lot.
So after PMM, they remain wet. Where to put them and where to dry them? Or do you always have to wipe it off before putting it away?

plastic in the dishwasher does not dry out unambiguously.

Straight surprised! Why do they stay wet after PMM? I wash my plastic containers every day (I take lunches / dinners for 3 every day with me), I always take them out dry. If you open and disassemble the dishes right after the squeak, then drops may remain in the grooves, shook them off into the sink and put them in place.

Straight surprised! Why do they stay wet after PMM? I wash my plastic containers every day (I take lunches / dinners for 3 every day with me), I always take them out dry. If you open and disassemble the dishes right after the squeak, then drops may remain in the grooves, shook them off into the sink and put them in place.

It all depends on whether you are using rinse aid or not.
If yes, the dishes will be dry, if not, the dishes and plastic will be wet, the plastic is stronger.
As I understand it, the "wetness" of plastic depends on the sliding of drops on the surface

It all depends on whether you are using rinse aid or not.

: wow: I never thought! My rinse aid is always filled, plus a pile-in-one tablet
We would probably need a different topic with PMM

Thank you!
We'll have to do the sink with a place for drying, I don't know what to call it.
And I just wanted to wash.
And I also did not know about the fact that the containers are wet due to the rinse aid.
We must try with him, maybe the problem will be removed.
Although, it is true, I have something with my hands, it must also be dried somewhere.

Consider the option of a sink with a wing - I liked it, I am on the wing and dry everything wet from the dishwasher

So, probably, I just wrote about the wing, calling it a place for drying)
It’s so, very convenient for me now, but outwardly I don’t like it. There are always a lot of containers to dry. Bardak)
And it's a pity for a place on this wing, although otherwise you just have to lay towels and dry.
Also not ice.