Ice cream maker Clatronic ICM 3225

[Lagri]

All advice I take into account. Thank you girls. I'm certainly a little at a loss. This is the first time I've encountered this. There was no such thing before.

Mine immediately. Warm water, not hot.

I also wash it with warm water.

To control the safety of freon, I would weigh the bowl on a scale and write down its weight in some commonly used ice cream recipe. And then I would control the constancy of the weight to make sure that the freon stays in place.

The bowl can be weighed constantly after washing and then it will be seen whether the weight is changing or not.

Lagri I had this, on a bowl in an ice cream maker! True, another ice cream maker Ariete 637. A refrigerant leaked out, the bowl was changed under warranty!

I really would not want to face this case, since I bought an ice cream maker in an online store.

The liquid that flows out of the bowl is at first transparent, and then turns white here is the photo! Is it the same for you? if so then the bowl cannot be used !!

My bowl is arranged a little differently, now I looked like there was no such thing. And she turned the bowl over: it gurgles inside, but does not pour out yet.

[Masha]

Masha, refrigerant may leak. Montis came to me all doused with blue liquid. I handed it back. But don't panic ahead of time. Wipe and dry well in the room. Check later if there are still smudges, for example in the morning. I did it once, too, but nothing happened.

Ksyusha, so you need to defrost it?

And after making ice cream and washing with warm water, is she still not thawed?

Do you need to defrost it all the time? I thought I could keep it in the freezer. What is wrong?

So she defrosts me herself. While I make ice cream, while I wash it.

If yours is not completely thawed, then this is most likely condensation.
Do not put in the freezer today, let it defrost. Take a look in the morning.

Already defrosting. Then I will rinse and check again.

The bowl has thawed and dried out - and everything seems to be fine, nothing flows. And yesterday, while the bowl was defrosting and I was constantly turning it upside down, it was leaking from under the sides for a very long time (and I was in sorrowful thoughts about what I was going to have ...) - and this was probably frozen water that remained after rinsing the bowl under the running water. So it turns out that you should always do this - defrost to the end, dry completely, and then in the freezer.

[Masha]

So it turns out that you should always do this - defrost to the end, dry completely, and then in the freezer.

Masha, yes - that's perfect!

I actually do it by itself, so apparently nothing froze and did not melt.

Girls, where do you keep the Klatronic bowl in winter? If you rarely use an ice cream maker in winter, I meant it ...

Always in the freezer, and a bag with frozen berries is included in the bowl. Everything is on alert, and then suddenly you urgently want to make ice cream.

Yes, I also kept the cup in the freezer. And then it got warmer and the meat from the balcony had to be moved to the freezer. So I think that the bowl can be stored at room temperature, albeit for a long time ... I have identified the instructions somewhere and nowhere to read.

Yes, I also kept the cup in the freezer. And then it got warmer and the meat from the balcony had to be moved to the freezer. So I think the bowl can be stored at room temperature, albeit for a long time ... I have identified the instructions somewhere and nowhere to read.

Of course you can, just before making ice cream, you need to put the bowl in the freezer.

: flowers: Well, let's eat the meat for the holidays and again I'll define the bowl in the freezer.

Makhno, please give me a link to the online store where you bought the ice cream maker (I didn't find it so cheap). Thank you in advance!

Girls! In Ashan (Moscow) there is a sale (promotion) - Klatronic is only 900 rubles !!!! Everything is factory sealed!
I bought it in early January for 1870r, can you imagine? And now -900! Who needs it, run! The machine is good! After freezing in a 35-degree freezer, it makes frost for ONLY 7 !!!!!! MINUTES.

[svetaastro,]

svetaastro,
Which of the Ashanov sells an ice cream maker for 900 rubles? Today I visited 3 Auchan on (Khimki, Krasnogorsk, Rublevskoe highway) in the first two there are Smile, in Krasnogorsk (on the other side of the Strogino MKAD) there was Clatronic (one piece, that is, a showcase copy), but not at all for 900 rubles. There are no ice cream makers at all on Rublevka

Here, in Mege- Teply Stan! Now I myself am going, however, to OBI ... Probably, I will buy another one ... You need to call: I will give you a PM.

Good day! Probably, I am a pessimist, but I am not friends with an ice cream maker, despite the fact that I tried to go around it throughout the last summer ... At first the ice cream turned out to be more or less hard, and then - thick sour cream ... After freezing in the freezer it turned out delicious crème brлеlée or frozen custard instead of normal ice cream, homogeneous, not airy at all. Such lush and light ice cream, like the store-bought one, is not even possible. And I read the reviews of the hostesses - they succeed ... Or I want a lot from homemade ice cream or am I doing something wrong Tell me?

[zumaE]

zumaE, the problem is most likely not in the ice cream maker, but in the freezer. Insufficiently low temperature. I, too, could not figure it out for a long time, every time I do everything the same, and the result is unstable. Sometimes after twenty minutes the scapula cannot turn, or even after forty - thick sour cream. I have a refrigerator with a crying evaporator, it turns out that there is a special heater, which melts the formed ice about once a day. Naturally, at this time in the freezer it is far from -18, the ice cream maker does not freeze completely and the mixture does not turn out fluffy.

[lot]

Thanks Jefry for the answer!
But if you find an option for a good freezing bowl, the ice cream turns out to be quite airy or still lot denser than the store? They say they add agar-agar to maintain airiness after beating the mass ...

Good day! Probably, I am a pessimist, but I am not friends with an ice cream maker, despite the fact that I tried to go around it throughout the last summer ... At first the ice cream turned out to be more or less hard, and then - thick sour cream ... After freezing in the freezer it turned out delicious crème brлеlée or frozen custard instead of normal ice cream, homogeneous, not airy at all. Such lush and light ice cream, like the store-bought one, is not even possible. And I read the reviews of the hostesses - they succeed ... Or I want a lot from homemade ice cream or am I doing something wrong Tell me?

I think for it to be airy, it must first be whipped well, while preparing the mixture.

[lot]

Thanks Jefry for the answer!
But if you find an option for a good freezing bowl, the ice cream turns out to be quite airy or still lot denser than the store? They say they add agar-agar to maintain airiness after beating the mass ...

I have agar, but I really don't want to add it there. What kind of airiness are we talking about? I pour 800 ml of the mixture into the ice cream maker, if the bowl is frozen "as expected", then the result increases in volume and does not fit into a "kilogram" bucket. Of course, it melts faster than the store one, but my fan club strongly opposes the use of any stabilizers.

Well that's it! Now I will try with renewed vigor in anticipation of seasonal warming, checking the temperature in the freezer, freezing the bowl and ... get ice cream! And then I blamed the ice cream maker and the mixer ...And I already wanted to change Klatronic for an additive to the Kenwood kitchen machine. But, judging by the reviews of the topic, probably not worth it.

I read Temka, it is immediately clear that people with nota decently long list of home appliances. Yesterday I unpacked it through the glass in the store, so beautiful, white, small. Well, I'm not capable of a feat - to buy a freezer, even for 6-7 thousand, where to put it, and who eats so much? And for Klatronic there is a good locker - a freezer. I'll go read the recipes, probably decide to buy!

And for Klatronic there is a good locker - a freezer. I'll go read the recipes, probably decide to buy!

and where did they take Klatronic?

Until nowhere Seen in 🔗

Well, I'm not capable of a feat - to buy a freezer, even for 6-7 thousand, where to put it, and who eats so much? And for Klatronic there is a good locker - a freezer. I'll go read the recipes, probably decide to buy!

Wasp, let's synchronize! I have the same story - I walk, I want, I scratch my turnips, and summer is getting closer ...

I am very pleased with my ice cream maker, I have just Clatronic ICM 3225. And I ordered it first for myself, then for two colleagues. But, in my opinion, only one I constantly make ice cream, and the rest make excuses: who has no time, who has components. Now, while my Clatronic is resting (Lent), but in a few days the bowl will safely move to its permanent place, in the freezer, so let's take our souls away.
If you like ice cream, buy it, you won't regret it

Wasp, let's synchronize! I have the same story - I walk, I want, I scratch my turnips, and summer is getting closer ...

Come on! I just ordered mine! Clathronic

Girls, I have a question, I somehow already wrote about this, but somehow I did not fully understand it. In my bowl: there is a gap between the aluminum and plastic bowls, not small, you can see it in the photo.
]
After washing the bowl, water seems to penetrate there and pour out for a long time. In the second photo, you can see if you press with your finger - the water is still there, and it's been a day since it dries. But if you turn it over, then the liquid does not flow. What is it? Do you have this too or are my bowls poorly glued or welded?

[Taia]

Taia, thanks for responding. It always annoyed me a little from the day of purchase, but I think maybe it is not necessary to completely remove the water from there, but to put it immediately on freezing. On the other hand, I think that if you do not remove it from there, it will turn into ice and spoil (crush) the plastic part of the bowl. Still, a lot of water is collected there after washing the bowl.

Come on! I just ordered mine! Clathronic

I'm a little behind you, but I'm already catching up - I took this miracle of engineering thought in Yulmart today !!!))))
In the evening I will put it on freeze and I will come up with a recipe to try

Can you please tell me, is the ice cream maker not big for one or two people?
How much ice cream can you make?
I choose between Clathronic and Vitek WX-1351-FL (it has a maximum volume of 320 ml).

Can you please tell me, is the ice cream maker not big for one or two people?
How much ice cream can you make?
I choose between Clathronic and Vitek WX-1351-FL (it has a maximum volume of 320 ml).

I pour about 600-700 ml of the mixture into Klatronic. And Vitek is small, I saw it in the window, I think, in MediaMarkt. I think it's better to take Clathronic - you can do less there if you don't need a lot. But the leftovers can be stored in the freezer ...

Girls and boys, help! Yesterday I wanted to make an ice cream for the baby, but the ice cream maker does not work: the timer is ticking, but the mixer is not spinning! I bought (ordered through the online store) last year, made ice cream a couple of times, everything was fine, but now what is wrong ?!

Check how the bowl was placed: the name, the inscription on the bowl should be in front, that is, turn the bowl 180 degrees. It was so with me.

Lagri, it’s strange that your water gets into the gap, I didn’t have this, I have been using Clathronic for 1 year.

Lagri, it’s strange that your water gets into the gap, I didn’t have this, I have been using Clathronic for 1 year.

And you don't even have such a gap?

Or do you wash the bowl in a different way? I also have a Klatronic for 9 months, but before, after making ice cream, I washed the bowl and put it right in the freezer, did not defrost it to the end.

ice maker does not work: t

Olya, how is your ice cream maker? came to life?

That's it, I ordered an ice cream maker and an ice cream spoon.

Who can say about Klatronic, is the timer knob easy to turn? Or with force, with a grinding and a creak?

well, not directly that would be easy. Slightly noticeable effort must be made.

Who can say about Klatronic, is the timer knob easy to turn? Or with force, with a grinding and a creak?

If you will. I will answer
My timer turns with light clicks, but not very easily, a little with effort, as is usual in an oven or a manual timer. But definitely not with a rattle and creak ..

Clearly, this means a problem ... like many people: at first the blade stopped spinning, I shook the engine and everything began to stir again, but now, to start the timer, you have to hold tight with one hand, and turn the other with the other. Although before that, in the very first start, in general, it was enough to turn the handle with two fingers.

[Lagri]

Girls and boys, help! Yesterday I wanted to make an ice cream for the baby, but the ice cream maker does not work: the timer is ticking, but the mixer is not spinning! I bought (ordered through the online store) last year, made ice cream a couple of times, everything was fine, but now what is wrong ?!

I wrote earlier, when I bought a timer from me, it was ticking, but nothing was spinning. I took it for repair, it turned out that during the transportation the ice cream maker shook and something was sealed inside. Maybe you are the same?
Lagri my ice cream maker has no gap, plastic adheres tightly to metal

So I shook the ice cream maker and now it starts up normally! There is a gap, if you tilt the bowl, then 3-4 more spoons of water will pour out from there

There is a gap, if you tilt the bowl, then 3-4 more spoons of water will pour out from there

And when the bowl dries up, no matter how I shake the bowl upside down, nothing flows from there. Of course, this gap would not have been better ...

[Lagri]

Lagri my ice cream maker has no gap, plastic adheres tightly to metal

What a score. Do you have Klatronic too?

[Lagri]

Lagri, my ice cream maker also has no gap and nothing comes out. Ice cream maker Clatronic ICM 3225. Has been working honestly for 1.5 years.

[Lagri]

Lagri, my ice cream maker also has no gap and nothing comes out. Ice cream maker Clatronic ICM 3225. Has been working honestly for 1.5 years.

So not everyone has this. Although other brands also have such a gap, Taia wrote, she did not have Clathronic, but another brand (only for some reason her message disappeared). I will try to ask the specialists (in the service center) why so ...