Dryer for vegetables Volter-1000

[Masha Masha]

Masha Masha, Congratulations! Yes, the dryer is a cool thing! And homemade marshmallow -

Kind people, hello everyone! Can anyone tell me if you can mix raw vegetables with jam to make marshmallow?
If so, in what proportions? I read somewhere that too sweet does not dry. We enjoy the acquired Voltera. Everything is overdried. The jam is in the basement - no one is eating. Maybe in his marshmallow?
Share your experience!

[Olga @ Olga]

Olga @ Olga, We have no experience in drying jam. I am sure that there is nothing to dry there. There is no water in the jam anyway. And sugar cannot be dried.
They made marshmallow from meadow strawberries. The berry without breaking the petal by the shaft into the electric meat grinder and all this slurry on the trays. If necessary, only the consistency was adjusted by adding some water. And once they brought a lot of strawberries and for one full load (10 pallets of 1000 Volters), everything did not fit. In order to avoid acidification of the already rolled mass, I had to add sugar to it almost 1: 1 and put it in the refrigerator. As a result, the marshmallow made of slurry with sugar turned out to be very cloying and undeniably lost to the one without added sugar. In addition, it was not possible to dry it to a completely dry state. So it remained sticky and all caked when stored in a container for storage.

So it remained sticky and all caked when stored in a container for storage.

It is enough to know the chemistry of sugar to understand that sugar-glucose syrup is viscous and will never turn into a dry layer.
Glucose syrup is often added to baked goods to keep it fresh for a long time, not stale.

Molasses, glucose - meaning and what to replace

Thanks for the advice!

The jam is in the basement - no one is eating. Maybe in his marshmallow?
Share your experience!

Making applesauce marshmallow. They used to add a little sugar. The pastille was sweet and dried perfectly. Then several times instead of sugar they added jam: sea buckthorn and blackcurrant. It turned out great.

I read somewhere that too sweet does not dry

It is possible this way. But moderately sweet, thanks to sugar, does not dry out and does not lose plasticity.

Can anyone tell me if you can mix raw vegetables with jam to make marshmallow?
If so, in what proportions?

We put that sugar and jam at the rate of about 100 g per liter. It turns out great.

Thank you so much! I will definitely try. Tomorrow.

Thank you so much! I will definitely try. Tomorrow.

By the way, it depends on sugar. Nowadays there is one that does not melt into caramel ...

We put that sugar and jam at the rate of about 100 g per liter. It turns out great.

So I tried to mix baked pumpkin puree with black currant jam. I also added an apple. Happened! The jam not only gives color, but also interrupts the pumpkin flavor, which not everyone likes. The pastille is delicious! Pavel, thanks for the advice!

[Paul I]

I also want to express my gratitude Paul I for his post # 263 from page 14, where he gives a technical description of Volter's insides with a photo, as well as Tan_ch for message No. 465 from page 24 about which thermal fuse you need to take, all this was very useful to me in self-repairing my dryer.
And now a new story from the life of my Volter-1000. As I already wrote above, I handed over my dryer to the service center for repair, since it stopped heating the air being driven. The reason was clear from the very beginning, because.here it has already been written about a similar problem and how it can be solved - the thermal fuse had to be replaced. I didn't wait and persuade it for a long time when my family did not repair it, I turned to the service department. After 3 weeks, I paid 1,500 rubles, after having checked the result of the repair on the spot, I took my girl home. But since I was preparing in advance for the drying season (it was spring), I did not carry out long-term repair testing, but simply removed the dryer until autumn with gas down. And when the time came to dry the marshmallow made from wild berries and pumpkin, my Walter did not dry the first batch - 12 pallets of marshmallow !!! Stopped heating again !!! The warranty for the repair has already passed, what should I do, bear 1500 rubles again !? No, this time I decided to act on my own. She ordered her husband what he wanted to buy, and demanded from her son to return the rosin and tin. He laughed for a very long time that I was going to solder myself, but I insisted on my own.
I disassembled my dryer, guided by Pavel's photo and found the following: there was no thermal fuse inside !!! The blown fuse was cut and the remaining ends of the wires were directly soldered. And I think that I was very lucky that the wiring that connects the heating coil to the mains burned out, and not the coil itself The wiring was soldered into place and a thermal fuse was added. Now my good girl is ready to work again! Thanks again, Paul I and Tan_ch
And this is, in fact, the process:



It's good that it ends well, but my indignation knew no bounds when I discovered such a trick on the part of the service center. They took that kind of money and shit so! I am writing all this so that those who have to contact such services are always on the alert and in a timely manner to fully check the result of the services provided, since you can run into unscrupulous snatchers everywhere.

[Ivanovna5]

Ivanovna5, Stunned

[Ivanovna5]

Ivanovna5, Anya, you gave it to the office. service?

[lettohka ttt]

lettohka ttt, Natasha, I'm surprised at myself. There, before soldering, it was necessary to disconnect 5 terminals, and how not to confuse them later ?! The decision came by itself: I signed paper tape - P.V., P.N. (top right, bottom right), etc., attached to the corresponding wiring and disconnected the terminals, and after soldering, put them in place and checked, whether there is heating, then she unscrewed it again in order to attach the plastic cover over the shade and the fan with screws and again easily and without difficulty inserted the terminals into their sockets. After that, I put the heating and ventilation unit into the dryer body, combined the screwing points and firmly connected the unit to the body. Now I am a MASTER, and I'm not afraid if the fuse goes off again, I have 2 more in stock By the way, these three thermal fuses cost only 100 rubles.



Svetlana, Sveta, yes. We have a network of these around the city.

By the way, Stebu's daughter also handed over to them, but at a different address, and also before the first turn-on. Probably, I will also sort it out at my leisure and see what is wrong there.

Here is the grief of the master Specially, that would be more often addressed to them.
Respect Annushka! and the budget is preserved.
My mom's microwave stopped working, asked in the workshop how much the repair would cost, she was horrified ..
As a result, the son disassembled it, changed the fuse, the price of the issue is cheap ..

By the way, these three thermal fuses cost only 100 rubles

Where did you get it?

Pavel, my husband bought them, I'll ask him tomorrow, now he is sleeping.

Good day to all!
I had a serious question when buying a Walter 1000 with a timer and email. control unit, since I found 3 official sites on the Internet))) 1) Volteralux34. ru 2) volteralux. ru 3) Voltaire 1000. RU
What website did you buy on? and Where is the official site all the same?)))
Having rummaged on the Internet, I determined that Voltera is produced in the Volgograd region, Volzhsky, OOO RosTechByt TD Voltera. And this model is simply not available from the manufacturer, but on the websites of those who indicated it is there, and the fear of buying a fake worries me.
What do you think about this? All the same, 5900 and plus accessories for it for 2000 rubles are not lying on the road.
Best regards, Oscar.

And this model is simply not available from the manufacturer, but on the websites of those who indicated above it is, and the fear of buying a fake worries me very much.

The fact that Walter is a clone of Isidri (I don't know how legal it is from the point of view of copyright) - do you know?
This is not the point. All "official" selling sites, as many have noted, put the price much higher than other simple sellers.
So far I have not heard of the forgery of Voltera, it is too expensive to make injection molds and organize assembly production, it seems to me easier to make a clone and release it under my own brand.
Therefore, feel free to look for a store with the most interesting price and delivery terms, especially since you are in Moscow.
Don't forget to buy at least 5 additional grills right away. Then you will understand why - as soon as you start drying!
As for the forms for marshmallows and nets - take your time if you are not an ardent lover of marshmallows. Honestly, it's a pity to give very unreasonable money for primitive devices that you suddenly won't use ...

In Moscow, there are these dryers, but the models are a little outdated, now the ESB VOLTERA 1000 LUX with a timer and e-mail has been released. control unit, its price is 5900, and unfortunately it is not yet available in Moscow.
And since there is no point in faking, then you can order with delivery (on the Volteralux34 website), by the way, components are cheaper there.
In any case, thanks for responding to my letter!

🔗 official store "VOLTERA" TRADING HOUSE

Help with advice! From which dryers do the marshmallow trays fit the Walter?

People! Help with advice! Bought Walter - 1000 Lux. There are no complaints about the dryer itself - it works perfectly. But pallets for marshmallow (one was included, the second was ordered additionally) curves came (the edges on both sides are strongly raised). I already kept them under load (for a long time), and watered them with hot water - they do not even out in any way. Advise on how to bring the pallets back to normal. And then the marshmallow flows down from the raised sides. By the way, for some reason I did not find anything on the Internet about a similar problem. And on the official website, someone asked the manufacturers about this, but, in my opinion, no one gave an answer there. I'm waiting for advice !!!

I bought pallets for Voltaire in NW on one of the forums.

Who would have suggested to me, not where else to buy pallets for marshmallow, but how to straighten the already purchased "curves"!

But I really regretted that I did not spend a little more money and did not immediately buy pallets that go for Isidri 1000 (they wrote that they are suitable for Voltera1000). Together with the Walter 1000 I bought their own pallets for marshmallows, as a result, after one season of use, they all bent, it became not convenient to make marshmallows in them, let alone dry small greens, and even more so. Very sorry ;((

It's surprising why no one writes about curved sheets for marshmallows from Voltaire-1000. Maybe it's just us we got some defective ones? Well, judging by what you wrote, you also failed to straighten them? And yet, maybe someone also faced such a marriage, and even figured out how to straighten the non-rectifiable ?!

It is impossible to straighten. I bought marshmallow trays from Isidri. The quality of the plastic is completely different.

I have been using Walter for two years and my two marshmallow trays are slightly deformed, but you can use it.
Here, if anyone is interested, I shot a video review / review

pallets for marshmallow (one was included, the second was ordered additionally) curves came

, as a result, after one season of use, they all arched

two marshmallow trays are slightly deformed

Girls, do you have pallets made of polypropylene or ABS plastic? Look here please.
Walter is now produced in two versions: from polypropylene and from ABS plastic.

[Song]

Song,
Pallets for marshmallows are made only of polypropylene. They are translucent.Another issue is the quality of polypropylene, or rather the characteristics. Since it was associated with plastic, I can assume that they took a more fluid material for processing, which is more prone to deformation. Most likely, they bought the cheapest material, the detail can be said to be secondary, they hoped at random. And as a result, consumers suffer ...

I also think about how to straighten it ") while I'm thinking about an industrial hair dryer") but did not decide how to do it

Pallets for marshmallows are made only of polypropylene. They are translucent.

Right, polypropylene. Not necessarily translucent. There may be white ones. It depends on what raw materials are delivered. Information directly from the manufacturer.

pallets for marshmallow (one was included, the second was ordered additionally) curves came (the edges on both sides are strongly raised). I already kept them under load (for a long time), and watered them with hot water - they do not even out in any way. Advise on how to bring the pallets back to normal. And then the marshmallow flows down from the raised sides. By the way, for some reason I did not find anything on the Internet about a similar problem. And on the official website, someone asked the manufacturers about this, but, in my opinion, no one gave an answer there. I'm waiting for advice !!!

She asked about the deformation of the pallets. They said that the deformation could be from improper storage. They advised to put them on a flat solid surface upside down, put something flat and even on top, for example, a dryer cover, and load something else on top. Keep them in a warm place for several days. Maybe it will help ... They say that even pallets are sent from the factory.

She asked about the deformation of the pallets. They said that the deformation could be from improper storage. They advised to put them on a flat solid surface upside down, put something flat and even on top, for example, a dryer cover, and load something else on top. Keep them in a warm place for several days. Maybe it will help ... They say that even pallets are sent from the factory.

About the fact that the pallets for marshmallow are sent from the factory even, it turns out that they are lying. After all, they went to me directly in the dryer and, in my opinion, they could not deform there. It turns out that either my pallets were stored at the factory warehouse anyhow, or it was still a defect. And their advice on straightening in my case will not work, since I practically started aligning my crooked pallets with this (then I invented this method myself and kept it under load for several days). As a result, at first, after such a procedure, they look equal, and after a few hours they return to their original curve shape. And yet, I still have a faint hope that there will be a craftsman (or some Vasilisa the Wise) who has miraculously coped with such a curvature.

Not necessarily translucent. There may be white ones. It depends on what raw materials are delivered. Information directly from the manufacturer.

Take my word for it, marshmallow trays cannot be white, in principle, depending on the raw materials. Primary polypropylene is never colored during its production. It is always transparent or translucent, depending on its appearance (I will not go into subtleties now). 😎 And additionally dyeing is an additional waste of dye! 😭
If polypropylene arrived at the plant in white, it means that it is, at best, recycled, that is, it is granulated from waste that was formed during the previous processing of raw materials somewhere else. Secondary raw materials you understand what quality - waste is waste. According to the usual rules, secondary raw materials can be added to the primary no more than a certain amount of percent - most often up to 20%. No one knows the quality of the waste, so it is very difficult to guarantee the quality of the final product🤣
Therefore, in this case, the only solution to the problem is to contact the affected buyer with the factory for a pallet replacement.True, one must take into account the following factor: some produce, others sell, no one wants to talk to buyers - hence the problems. There is a complex structure. I know this manufacturer well ...

About the fact that the pallets for marshmallow are sent from the factory even, it turns out that they are lying. After all, they went to me directly in the dryer and, in my opinion, they could not deform there.

And their advice on straightening in my case will not work

marshmallow trays cannot be white in principle

You can call and ask yourself. Here is the phone number of the sales manager of the Volter plant

8-8443-568988; 8-906-409-7745

I only voiced what I heard.

I know this manufacturer well ...

I don't know him at all, I just called and asked. Maybe they will tell you something else ... And you will tell us.
We are all interested in the quality of the purchased goods.

I don't know him at all, I just called and asked. Maybe they will tell you something else ... And you will tell us.
We are all interested in the quality of the purchased goods.

I'm afraid that in my particular case it will not be economically profitable at all because of the two pallets for marshmallow, to start large-scale negotiations with the manager of the manufacturing plant (while getting on roaming), and then still paying transportation costs for the delivery of my marriage pallets to the plant and new ones pallets to my Tver. And where is the guarantee that the quality of the newly sent will be normal. So you probably have to take from Isidri - there seems to be better quality !?

[angela]

angela, the quality of the pallets is good. I have been using it for the second year, no complaints.

I got it weird
I bought an additional 9 trays from the seller along with a dryer
it turned out that 1 was included (transparent) and 9 translucent white
and transparent turned out to be the worst (marshmallow spilled)
when the dryer almost caught fire and burned down the house (yes, this is the quality of the dryer ... I recently passed it under warranty), then the transparent pallet shrinked the most, and the rest are decent

the quality of the pallets is good. I use it for the second year

And not everyone complains about Walter. I specially reviewed a bunch of reviews and videos on YouTube, everyone seems to be happy. And even here complaints have just appeared.

almost caught fire

Horrible. But they write about the degree of protection and so on.

Horrible. But they write about the degree of protection and so on.

that's the catch
I thought that everything is fine, everything is fine, but then, for no reason at all, the incandescent thread began to work as soon as you plug it into the cutter and fry so that it becomes light from the brightness of the thread and melted
I'm waiting for what they will say under the guarantee and I will write in accordance with this review (s) about the "wonderful" quality of the dryer that worked normally for exactly 364 days (okay, the warranty was 2 years when I bought it, but now they only give a year)

I do not use it myself, but Voltaire's friends have, I don’t know the truth, whether they use pallets for marshmallows. But they dry a lot of things and are happy!

For some reason, the topic only discusses the problems of the dryer, of course it is necessary, but let's dilute with positive results
This is what kind of dried cherries I have been making according to the Admin recipe for the third year already, it turns out so yummy

at first I did everything strictly according to Tatiana's recipe

and then simplified it a little, the result is the same

I ask for help !!!!
Yesterday I dried apples and found that the heating had stopped turning off. The fan runs, heats up constantly, the heating lamp does not turn off.
What to do? I look forward to your advice
There are a lot of apples, the dryer is urgently needed in working order.

[Svetlana]

Svetlana, and if you call the service department?

[Svetlana]

Svetlana, and if you call the service department?

Anya, won't give a ride, I think. They need to cut money, not give free advice.
If Pavel was on the forum, he would have suggested, but he was gone for a long time. Summer, vacation

[Svetlana]

Svetlana, most likely the thermostat or temperature sensor is faulty, I do not know what is there.

[Olga]

Olga, Olya, we also decided so. We are looking for where to buy the required thermostat.

[$ vetLana]

$ vetLana, Light, good luck. We also went through a breakdown in the season. The power button is stuck and the dryer is under warranty. The service was waiting for a replacement from the factory for half a month. Now we have bought a few buttons in stock.

Anya, won't give a ride, I think.

Here is the phone number of the sales manager of the Volter plant

8-8443-568988; 8-906-409-7745

The second phone is sort of a factory service department. Try it, call.

[Alena]

Beautiful girls! Tell me where on the forum you can place an advertisement for the sale

dryers Volter 1000 Lux? Selling mine. I have 7 such new ones, 3 pcs with an electric control unit (with a timer (ECU)), a maximum of 15 sieves, 10 mesh and 10 pallets for marshmallows, and 4 pcs with mechanical temperature control from 30 to 75 C + a separate timer. Dryers are new, in boxes, never used. I bought it as equipment for business, but because of the upcoming move to another country I am selling it. : girl-swoon: I will give it at cost price: 14,300 rubles / 1 set with an ECU and 13,700 rubles / 1 set with mechanical temperature control.
If you hit the topic, then those who want to buy call: +79772665654 Alena.
You can pick it up in the city of Smolensk or send it by delivery service to any other settlement by agreement.

Alena, you need it in the Flea market. We have such a topic. Notice board (for sale) # 902