Problem situations in the operation of dishwashers

[HelenaAlex]

HelenaAlex, the instructions should definitely contain a description. And on the control panel there are probably drawn lines with the caption "Reset". I have two buttons that you need to hold down and turn on the machine after that. Or vice versa, hold it on and off, it doesn't matter. You can always try this and that to the desired result.)) Surely the control of your car is different from mine, so consider for yourself.

On mine, to cancel the program, you need to hold the START button for a long time
I found out by typing. There was no instruction (pm asco)



on the other, which is in Moscow, press and hold the button for the program you want to cancel. (aeg old lady)

And she pressed it and turned it off from the network, it still drives the program, piteously squeaking.

runs the program anyway

then call a friend, that is to say, officials

And she pressed and turned off from the network

the instructions for your car say:

Yes, I probably pressed too quickly for less than 3 seconds.
So I sausage for 3 hours on the eco program

here ... how much smarter the machines are than us ...

how much smarter machines are than us ...

we just never have time ...

And what is this Aquasafe, just Aqua-Stop blocks the water

I have a Flavia dishwasher, it also has an aquastop function. You can be calm :)

Good morning! I have a question for those in the know. My car broke down, narrow Bosch. What to prepare for with such signs:

1. Does not wash away from above or below
2, Does not drain
3. Doesn't heat
4. Does not dry
5. Hangs at the end - 1 min. without the end of the regime
6. Failure modes - shows more
a short time in all modes, after Reset shows normal time, but does not work

[Antonovka]

Antonovka, for a start, you probably need to make sure that the electricity is supplied to the outlet of normal voltage, and not a weaker one, which is enough to turn on, but not enough for normal operation of the PMM.

[OgneLo]

OgneLo,
Marin, the electricity is all right ((

[Antonovka]

Antonovka, 1) Water block, 2) Electronics block.

[sazalexter]

sazalexter,
In short, everything is expensive (((I already think if the repair is very expensive, then it's easier to buy a new one for 17 thousand

It seems that the PMM is broken (narrow Siemens, insertion). Stopped during washing. The pump hums, but does not draw water. On the board flashes "faucet" and error E15. There is no water in the cell below.
What can it be and can you fix it yourself?

Threat Google says that E15 - Aquastop leakage protection has worked (?).

error E15

there may be several variants of this error, including:

Error E15 informs the user that the "Aqua-stop" leakage protection has worked. This means that water has entered the pan of the machine or the float has stuck.
The reasons for water leakage can be the following:

• Leakage sensor defective.
• Clogged drainage system (filter, hose, drain).
• Worn connections or poor sealing.
• There is a defect in the water spray.

Source [https://Mcooker-enn.tomathouse.com/s-image/1010/oshibka-e15-bosch/]

[Manya]

Manya, didn’t use any new detergent, by chance? For me, aquastop worked on somat powder at one time, I had to pour less.

[girls.]

Thank you, girls.
Tina, no, I haven't changed the detergents, I've been using Somat in tablets for a long time.

She cut off the power and turned off the water at night. Now everything is turned on, there are no errors on the scoreboard. Has started a short washing program - it works. : - Dry? Do you still need to disassemble?



Eh ... have to disassemble.After 25 minutes of work, I issued E15.

[Sonadora]

Sonadora, Manya, I am so sorry.
My Siemens and I have suffered with this problem for a long time. As soon as the powder was not the same, or to pour in more - the aquastop worked. When disassembling the machine - either the water is in the pan, or it has already dried, but traces of foam.
Sometimes a few days of drying helped, sometimes not.
In the end, after a few years, they found out the reason. The water tank was leaking, apparently, at first a little bit, then more and more and the master was able to detect it. After replacing the tank, there was no E15, but I still only use Finish powder and a little.

And mine just died to NG - the engine, neither new nor used in normal condition could not be found. Now I have a kind of fancy Beko, but this, unfortunately, is not my simple Bosch (((

If you suddenly find a sharply dimmed glass or rainbow stains, then it's time to lower the settings.

Lenochka, please tell and explain in more detail about this.
Indeed, rainbow stains appeared on brown glass cups and plates. The clear glass cups are cloudy. And the cups are double, dear ones. It's a shame

I've been waiting for the salt and rinse aid icons to light up. And they still can't. Mine almost every day in PMM. It is a pity, I didn’t write down to myself how long ago I poured and fell asleep in it.
Lena! What need to do? To shift the vicarious side Settings? I don’t understand, the water didn’t change its hardness.
I have a hmm Siemens.

[Tanya-Fanya]

Tanya-Fanya, followed the link to your post. This was the answer HelenaAlex after her words about what she has Regeneration settings set to maximumbecause the water is hard. She washed with a kind of powder, but complained that the salt flew away too quickly. Here I reacted to what was highlighted with these words.))

Because the acceleration of glass degradation is caused precisely by the increased alkalinity of the cleaning solution. This can be 1) water with an increased amount of soda (the sodium that the resin previously took from the salt), 2) overly aggressive detergents with a high alkaline reaction (or their high concentration), and 3) too high washing temperature, which accelerates chemical reactions.

From this it logically follows that at the first signs of pathology on the dishes, we need to change the quality of the input. And what will have to be reduced there, everyone must figure out for himself. If your regeneration has a high value (but then a lot of salt would go away, but this is not), then lower it.

I didn't understand how the dishes are washed ... If with tablets, and the water is not so hard that the kettle needs to be descaled after each boil, then you can generally try to regenerate to 0 or 1, IMHO. If I wash with powder, then when washing beautiful dishes, you will have to reduce the degrees of washing or the amount of powder.
And make a rule not to put valuable dishes in the lower basket.

Are the main points clear?

What it can be and can you fix it yourself

The gasket of the pressure switch and (or) the temperature sensor could leak

[SvetaI]

SvetaI, Svetlana, thanks, I will keep in mind. Probably, it was a factory jamb, if the stainless steel tank leaked.
sazalexter, Alexander, thank you. A gasket is very likely.
Today, when Aquastop worked and opened the machine, steam went straight out of it, although the sink was 45C degrees.

[Bijou]

Bijou, Helen! Hats off, smart girl !!!

Lena, here I read you and thought ... I washed the tablet for two years the finish all in one. Last month I got hooked on the finish line of Quantum Anti-Fat. Pmm inside with them very clean.
My water is terrible. Mine by car. I set the regeneration at 4 according to the book and indicators.
Conclusion: hefty good pills? Reduce regeneration to 1?
Rinse aid for 1 too.

Thank you very much for the help!

Last month I got hooked on the finish line of Quantum anti-fat.

Uh .. And after that there were problems with the glass? Or was it before? Just one word "anti-fat" worries me in this context, because all kitchen tools for breaking down fat, as a rule, contain an increased amount of alkali, namely caustic soda, NaOH (aka caustic soda and sodium hydroxide). It's hard to believe that such a thing is present in the dish detergent (rather, maybe in the dishwashing detergent for the machine itself), but the very direction of my fears is understandable?))

The water is awful what's this? Straight scale, scale? Then the four of regeneration is normal, less exposing is fraught with scale on the heater.Decrease to three does not seem to me such a panacea in this situation.

Auto is what degrees? 45-65? There really is nowhere to reduce ...

Remember more about the state of the dishes until the last pills and look for a way out by experience. Maybe half a tablet will be enough for washing? Or alternate with milder products.

Auto is what degrees? 45-65?

And what is AUTO in your opinion? My temperature on Auto does not change, always 65 degrees. The only thing that can change is the time, 6 minutes before the end of the program, she tests the water with an aquasensor and often adds another 28 minutes. Do other PMMs work differently for AUTO?

[Bijou]

BijouThank you very much again.

The water is exactly like you said "scale sits on the scale and drives the scale."
Auto in the range from 45 to 65 g
I started to change pills intuitively. Finish Quantum anti-grease put only when very dirty dishes.
I will continue to watch.




lega, for Siemens and Bosches, the auto program heats the water from 45 to 65 degrees, depending on how dirty the dishes are.
And there are separate modes to which the temperature is clearly tied, like in washing machines

for Siemens and Bosch, the auto program heats the water from 45 to 65 degrees, depending on how dirty the dishes are.

Does the PMM choose the temperature itself or do you need to set it somehow? Does the aquasensor detect pollution?

Mine also has separate modes, but there the time cannot change, that is, the aquasensor on these programs does not turn on. (I think so, maybe I'm wrong)

Yes, it is the aquasensor that determines by the first dirty water. He will also set the temperature, and may change the time a little.

I think Guru Biju will correct me and more accurately explain to you. My knowledge is just from the instructions

[Tanya-Fanya]

Bijou, as it were, owns exclusively open information.)) About the aquasensor, an inevitable belonging to auto programs, once upon a time I met the following:

Aquasensor3 is a necessary thing, it determines the degree of soiling of the dishes, determines the most suitable washing temperature (one of five), and includes one of 48 washing programs (differences in intensity and duration)

So that Tanya-Fanya absolutely right.

We fixed the PMM. Aquastop was triggered due to wear of the wash tank glass seal.

[Sonadora]

Sonadora, Hurrah! Hurrah! Hurrah!
Manechka, I'm sincerely glad! Congratulations! Let your assistant "do not get sick" anymore 🌺

Good afternoon everyone! I had a problem with the dishwasher, at first the dishes in the machine did not dry, we began to change the settings in every possible way and noticed that the air conditioner that we filled in is absolutely not consumed have already done 7 washes, what could it be, what could be the reason that the air conditioner remains in the compartment?

The Beko dishwasher is digging in the bottom corner, the bottom seal has been changed, the leak has decreased, but the leak has not been completely eliminated, what else could have happened? The powder was not changed, mine with this tool for a long time.

what could it be

The flow rate of the amount of rinse aid is not set, the current setting is "set to zero", as an option, the air conditioner supply channel to the machine is clogged.

everyone who has a white coating, I also had it - after 3 years, the water is hard about 300 ppm, washing with salt and liquid power
replaced the resin and helped

replaced resin

What kind of resin?

What kind of resin?

in the ion exchanger, after years it turns out that the ion exchanger ceased to perform its function, and there was a white coating on the dishes, after replacing everything is ok, there is no plaque wash for 10 years

[Jungo]

Jungo, we have such an incomprehensible situation ... We live with friends in different parts of the city, the distance is very small. We use the same means, but everything is fine with me when washing dishes, my friend has a strong white coating from the very beginning.
They moved from district to district, and the car washes in the same way, the dishes with a white coating were from the tap water and now, after their move, when the house has a personal pump with a pump, it has been in use for 4 years, but there is no difference. Why, why?
I think there is something wrong with the car.
Can you tell me something?

[Ilmira]

Ilmira, and replacing the resin did not help them?

[Ilmira]

Ilmira, and replacing the resin did not help them?

chef, I have been using the car since 2002, but what kind of resin is in it, I don’t know

[Ilmirushka]

Ilmirushka, Clarify whether your friend uses salt or tablets, whether the hardness is set correctly on the PMM. Replacing the resin is an extreme case. Through the service, if with official materials it is quite expensive. Through a private master, the resin from the water filter is still tolerable. You can try to revive the filter by setting the hardness to maximum and washing 7-8 times without dishes and detergents

Please help me solve the problem with my dishwasher. The pill stopped dissolving, sometimes the box was closed sometimes (like yesterday) it was opened, but the pill is intact. I have tablets in a dissolving shell. I tried to shoot it, mistakes happen anyway. Can I just throw a pill on the bottom of the machine? Or crush and pour the powder?

Can I just throw a pill on the bottom of the machine?

You can just throw it into the car, but you don't need to grind it. Although the washing algorithm in many machines includes rinsing without detergent and determining the degree of contamination by the transparency of the flush

Check if your friend uses salt or tablets, whether the hardness is set correctly on the PMM.

Everything was done according to the instructions, and the salt was poured, and the rinse aid was poured. For washing, both 3-in-1 tablets were used, and the powder was sampled.
I can't say for sure about the water hardness regulator, I didn't look at it myself, but she says that her husband checked everything.

I tried to shoot it, mistakes happen anyway. Can I just throw a pill on the bottom of the machine? Or crush and pour the powder?

They also put the pill in a container-basket for spoons-forks.
........................ ........................ .................

Everything was done according to the instructions, and the salt was poured, and the rinse aid was poured. For washing, both 3-in-1 tablets were used, and the powder was sampled.

My dishwasher is 10 years old. All settings are checked - rechecked, salt rinse sensors are set, all detergent manufacturers are tested. I already know the instructions for the dishwasher by heart. But there have always been divorces. I've already resigned myself.
But recently I began to use Fairy capsules - the result is perfect. With the same settings, water, salt and rinse aid.

For washing, 3 in 1 tablets were used, and the powder was sampled.

When switching from tablets to powder and vice versa, you need to take into account that not all machines are reconfigured automatically, for example, I have to manually switch to a tablet, check this moment

[sazalexter]

sazalexter, Alexander, Thank you. But there, most likely, something different because the detergents were not changed daily. We used the powder for a long time - the quality of washing is just terrible, we tried to regulate it, it did not help. We decided to switch to pills - and nothing has changed either.

PMM Siemens, 8 years old, Teng died. The water does not heat up, it gives an error during drying.
From the "pleasant" - the unit is not separable, the heating element changes with the pump. The master will come tomorrow.