Dishwasher malfunctions

That's why I do not like neither Ariston nor Indesid

And now I probably will not like gas panels, but only electric ones.

[Stafa]

Stafa Induction cold like a "dead man's head"

[Stafa]

Stafa Induction cold like a "dead man's head"

, I just cook for scrambled eggs and spaghetti, and boil a kettle, I'm not ready to part with thirty thousand rubles for these actions.

[Stafa]

Stafa Tiles for 7000 rubles https://Mcooker-enn.tomathouse.com/index.php@option=com_smf&topic=731.0

[Stafa]

Stafa Tiles for 7000 rubles https://Mcooker-enn.tomathouse.com/index.php@option=com_smf&topic=731.0

And cover the hole from the panel with a rag, and change the tabletop - then you can look at the single-burner induction. But I can't see a new tabletop - it's just electric glass-ceramics like Samsung touch. Cheap and angry.

Girls, with a century ..... I once again ask you! Who tried to test the machine on the maximum salt value, PLEASE try to run the machine again on a short program, only with r = 4 (if 5 is the maximum value), that is, I ask you to set the salt value to "one" less than the maximum. .. It's just that I "understand my thoughts" ....

I ask the audience for help. Please, PMM ARDO, almost a year of work. Water began to collect in the pan. The machine was not disconnected from the water supply every time. There was a drop with water, after that it happened. The hoses and drains were checked - there were no kinks, the drains were not clogged. They turned off the water supply to the machine - water does not run into the sump. They turned on the water supply to the PMM, while not a single program was set, water began to run into the sump again.

And I'll write more right there. The salt fell asleep a year ago, it is still there, more than half. Do you need to fill it up?

[Grypana]

Grypana In service, especially since it is under warranty. Very similar to the failure of the intake valve. Add salt when the indicator goes off, although you can just add salt.

Thank you!
And now I got all the documents for my PMM. Date of purchase 29. 06 So the year has already arrived. One year warranty has expired, but there is still 2 years of warranty service. As I understand it, the work is not paid, but only materials. Second point. The warranty booklet contains sections in different languages. And so I saw that the warranty card was filled out on the Kazakh page, and not on the Ukrainian one. Model, store stamp, date - everything is present, there is no serial number. Is this "Kazakh" filling a violation or a reason for denial of service? In theory, I think not. I'm just getting ready to talk with the serisniki and I need to be fully prepared, so to speak.

Need your help ! the Veko dishwasher has broken. The dishwasher is already 6-7 years old. The problem is this. Recently, water runs into the dishwasher (when it is turned off), and recently, when turned on, the drain turns on and buzzes and does not turn off (that is, when I plug it into the outlet, the drain (or pump) immediately turns on and works until you turn it off from the outlet, the programs do not respond to the buttons either The drain hose was checking the water drains. Recently I added a couple of drops of Ferry to the machine (since there was a lot of foam, but the machine was working) The filters inside are clean. When you turn off the pump, water flows into the dishwasher from the bottom where the filter is inserted. Maybe something is jammed?

Need your help ! the Veko dishwasher has broken. The dishwasher is already 6-7 years old. The problem is this. Recently, water has been running into the dishwasher (when turned off), and recently, when turned onthe drain turns on and buzzes and does not turn off (that is, when I plug it into the outlet, the drain (or pump) immediately turns on and works until you turn it off from the socket, it does not respond to the buttons and the programs do not turn on. What could it be? The drain hose was checking the water. while adding a couple of drops of Ferry to the machine (since there was a lot of foam, but the machine was working) The filters inside are clean. When the pump is turned off, water flows into the dishwasher from the bottom where the filter is inserted. Could something get clogged?

I have an Electrolux. And this is how you describe, since it happened that the machine began to hum and only after turning it off did it stop. We decided everything over the phone. It's kind of like "aquastop" worked. There is a pallet under the car and water dripped into it, the husband gently soaked it with a cloth, and the machine started working.

[Natawa]

Natawa According to the symptoms, the machine cannot drain the water to the end, hence the work of the pump. The reason, the saving of detergents, is very similar to the clogging of the inner part of the car with grease, I met something similar on the Internet, I don't remember where ... Call the master.

Thank you! it seems everything is clean there, but in the dishwasher itself, the water immediately fills itself after I turn it off

Thank you! I will call the master. I didn't save money, I always poured almost full, but a couple of times the last added ferry to the powder

[Natawa]

Natawa After washing, try to immediately turn off the water tap at the entrance, whether water will leak or not, there may be a malfunction of the inlet valve.

So the dishwasher does not wash, only the pump hums, and the water is drained, and then immediately the water appears where it is drained. But buttons don't react at all

So the dishwasher does not wash, only the pump hums, and the water is drained, and then immediately the water appears where it is drained. But buttons don't react at all

Call the master! I hope not like my breakdown!

annnushka27 what did you have? can tune in to buy a new one?

annnushka27 what did you have? can tune in to buy a new one?

Oh, maybe there is a small breakdown! Most likely true, problems with the inlet valve. My engine burned out, I wrote a couple of pages ago.

Please tell me, can anyone have it. There is dirty water in the dishwasher under the filter. Cleaned filters did not help. She turned on to wash the dishes, the water seemed to be pouring there, but somehow quietly, not as usual, you could not hear the jet hitting the dishes and did not make as much noise as usual, as it was too quiet. Since that was, I cleaned the filters and everything worked fine, but now it did not help.

Please tell me, can anyone have it. There is dirty water in the dishwasher under the filter. Cleaned filters did not help. She turned on to wash the dishes, the water seemed to be pouring there, but somehow quietly, not as usual, you could not hear the jet hitting the dishes and did not make as much noise as usual, as it was too quiet. Since that was, I cleaned the filters and everything worked fine, but now it did not help.

just a couple of pages ago someone had a similar problem .. look back two or three pages ... .. there the guys already answered what to do with it and where to "look" for the problem ...

Please tell me, can anyone have it. There is dirty water in the dishwasher under the filter.

The sewer may be clogged. But actually there should be some water left in the filter.

She turned on to wash the dishes, the water seemed to be pouring there, but somehow quietly, not as usual, you could not hear the jet hitting the dishes and did not make as much noise as usual, as it was too quiet. Since that was, I cleaned the filters and everything worked fine, but now it did not help.

And the dishes are clean as a result? The volume of work is a subjective concept.

Thank you, I will read it now. I didn’t wait until the end of the program, because I could hear something was wrong. And when I open it, only trickles flow there, a little water, and usually much more.

Run an empty machine on any program, if there is a simple rinse. When water is collected and the pump starts to work, slightly open the door.The inside of the machine must be evenly splashed with water and completely submerged in the pan.
If there is not enough water, cleaning may help. This is a run-through of an empty typewriter on the hottest program with special equipment.

Do you clean the rocker arms? They also get clogged.

Ok, I'll try to unload the dishes. The rocker arms are also soapy. did not help. Yesterday only the salt fell asleep, it could not affect? maybe where did you go wrong?

Girls, I have a dishwasher problem too. Maybe someone will give advice. The salt indicator does not go out. I fell asleep a lot, as it is written in the instructions. At first everything was fine, the indicator went out and did not bother for two months. When it lit up again, I added salt, but now it does not go out, and the salt is taken by the stone and does not dissolve, although we constantly stir it. I use pills, so I think, maybe you don't need to pour salt at all if you use pills?

Run an empty machine on any program, if there is a simple rinse. When water is collected and the pump starts to work, slightly open the door. The inside of the machine must be evenly sprayed with water and completely in the water in the pan.
If there is not enough water, cleaning may help. This is a run-through of an empty typewriter on the hottest program with special equipment.

I pulled out the dishes, washed the filter again, turned on the rinse and the machine started working as usual! the pallet is completely in the water. Then an empty typewriter should be driven away? or what could it be?

The instructions for my car recommend periodically running an empty car with detergents at max. temperature. After cleaning all filters, etc.

I bought the Finish product, I'll do it today

Good day to all!!!
Tell me, plz!
Whirlpool wp79 \ 1, purchased in 2006. I turn it on, the machine starts working - it draws water, works for about 30 minutes and stops. I open the door, then close it - it immediately continues washing. Then it stops again, and if you open and close the door again, it continues washing. If you do not open the door after stopping the machine, at the end of the programs, after the time has elapsed, it simply drains the water, dries and beeps that everything is ready!
After cleaning the filter at the water inlet, it stops 50 minutes after starting. Before cleaning, the first stop was in 20-30 minutes.
On the phone, she explained the situation to the master from the service, he would think he said.
This machine is in the apartment, there are no voltage drops (mmm)

People! Good day! Please tell me what can be done in such a situation: At the bottom of the door the sealing rubber is slightly jammed, now it is leaking in this place. Is it possible to straighten it somehow? Does anyone have any ideas? Thank you!

I unscrewed the filter today to wash, and there is water. What to do???

I unscrewed the filter today to wash, and there is water. What to do???

I also have water there, the filters are not completely covered, but somewhere in half.

I don’t remember how it was before .. but now right to the edge with the "floor".

The first step is to check if the sewer is clogged.

Zhenya, for those who are in the tank .. how to check ??

The first step is to check if the sewer is clogged.

Zhenya, is this not a water seal? I also have water there, though just below the "floor".

Miracles .. now I looked, the water is gone altogether .. can be seen only at the very bottom .. even below the filter ...

I didn't pay attention before, maybe the water level fluctuates inside

At the beginning of the fast program, the car beeped for me, and water poured onto the floor. Such a problem already existed, a friend put the machine on its side (I have a Candy-trio) and picked out the fat from the drain hole on the back surface. But the machine worked for 3 years before. Now the situation repeated itself a year later. Now I restarted it for a long program - while it works. I called a friend who was repairing it - he advised to remove the filters, pour the Mole into the hole and pump it with a plunger.I doubted something - after all, the dishes are washed in them, will there be no alkali after washing?

Girls, advise what to do. Beko dishwasher built-in, I use it for a year and a half. Recently, after two or three washes, a very strong greasy deposit has formed on the filter, you have to remove the filter and wash it all with difficulty. I ran out the cleanser, I regularly wash the rocker arms, but the PM inside is somehow sticky. I use somat powder and rinse.

[blush]

blushThe first thing that comes to mind is that the machine washes in cold water. Check, open the door during washing, the water should be about 50 * C. Second, the amount of powder is greatly underestimated. Third, fake powder.

I have grief Our PMM Electrolux ESL46050, having served us faithfully for 3 years, decided to break down. I started to give an error about overflow. The husband disassembled, it turned out that water was collecting from somewhere in the lower pan, as it reached the sensor, the machine was cut down. The water was drained, worked for another week and again for the old one. They called the foreman, he twisted and twisted, found two holes (it is difficult to even call them holes, the welds parted a little) in the body itself, that is, in the tank. The master said: "It's time to bury", did not do anything. But it's a pity ... Maybe someone has experience, do you think, if you cover it up with a sealant, will survive? As I looked at the prices for new ones, more or less decent from 16 sput starts

[Irina]

Irina, I had exactly the same trouble with exactly the same machine. Only she lasted only 2 years. And no one undertook to repair either. Now I have Bosch.

[Kara]

KaraIn general, I would try epoxy compositions like "Cold Welding" 🔗 , you can risk plumbing silicone, but it has worse adhesion to metals and is plastic, in contrast to cold welding. In general, the sealant should adhere well to metals, withstand 70 ° C hot water and be alkali resistant. There are rubber-based sealants, you can try them.
PS: Moreover, a husband with hands

Alexander, thanks for the tip, we will definitely try. We will report

Hello, tell me what the problem might be. I have a hotpoint ariston adls 7, the pre-rinse program does not work, you can hear how the water is gaining, then it drains and the signal about the end of the program is on, and the dishes are dry, while the sink just works and everything is washed, but what about without pre-rinsing?

[Galya13]

Galya13, It's hard to say, it looks like "brains", only the service will help here. In principle, it is possible to do without pre-rinsing.

Alexander, thanks for the tip, we will definitely try. We will report

In general, we buried our Elusha
They smeared the entire body, all the seams with entoy cold welding, after 4 days - again it gave out an overflow. Well, we sent her to trash can rest
Now we have Bosch SuperSilence SPV63M50RU. And it seems cool, not the cheapest, but I just can't get used to it. It washes perfectly, of course, but it dries sucks, most of the dishes remain wet (they say this is because it has a fundamentally different type of drying, a heat exchanger), I also liked the interior arrangement more in the electrolux. In general, I'm getting used to