Dishwasher malfunctions

I have a DIN 26220 eyelid and a small DIS 1520 and a question about the salt setting

I have a different model, but maybe the salt setting will work. Everything is done with buttons on the panel.
With the machine off, press and hold the program selection button and turn on the machine.
Release the program selection button. The corner G and the number of the hardness level will light up on the panel.
Start / stop indicator blinks. Change the hardness level with the delayed start button. Use the start / stop button to fix the indicator and the start / stop indicator lights up continuously. We turn off the car.
Here's a tricky combination.

washing on a long program with dishwasher cleaner

Do you mean that the car itself was washed with a special detergent?
I do it every month! that is, on the last weekend of March, the machine was washed.

we do not have powder on sale

This is more than strange. On hard water, tablets, in principle, cannot achieve normal washing quality, there is no water softener in the tablets, only carbonates and zeolites, in the presence of which hardness salts fall out in the form of flakes.

Do you mean that the car itself was washed with a special detergent?

Yes

I do it every month! that is, on the last weekend of March, the machine was washed.

Whoa! I don't wash mine ... Installed in September 2017, but I constantly add salt and rinse, and constantly change, then powder, then tablets ... Well, the modes, also alternately. Once a week, I definitely include a long program.
I wonder if I need to wash the car?

I ask for help.
Out of the blue, something happened to the dishwasher. She picks up water, tries to wash it, but the water does not heat up. Rinses, rinses with cold water, then drains, the drying icon turns on, blinks for a while, then the icon suddenly turns on that there is no water.
At the same time, foam remains at the bottom of the dishwasher after draining, although I turned it on without any product (well, if only it is rinse aid?)
What are the reasons?

And what error does it give? My ten was covered, I wrote E09. Until they have repaired, they announce the amount from 10 to 15, a huge toad presses on the throat, but it's already sick without a dishwasher.

mine does not have a display with an error code, the "Faucet" sensor is flashing.

[Wiki]

Wiki, look at the sink and all that. It was similar when the drain hose froze in winter.

With the drain, everything is fine.
She does not heat the water, washes it cold, then stops drying and gives an error - a blinking tap.

Girls, my PM stopped working last summer, for some reason the e-mail was turned off. Woe to the repairmen, who just didn’t speak and ten burned out, that her brains were broken and the whole unit had to be changed and a lot of things (well, very bad people ...), the last one ... removed the temperature sensor from her (it seems so this little garbage is called) took a lot of money for it (4500) but against others who wanted to repair for 9000, 10000, etc. it turned out to be tolerable for us and the car started working without a sensor, this grief repairman told us that the manufacturer is a fool and like no one needs this sensor. The husband took the sensor from him and went to the Internet. As a result, the sensor is of course needed (precisely because it burned out, the machine stopped heating the water and turned off and it is needed for control). The husband himself bought this sensor (200r seems to have cost) and installed it himself. In general, the conclusion that we have drawn, all these repairmen ..., few of them understand something, they do it by typing, and we are forced to pay for it. Be careful and do not buy right away, do not pay for expensive spare parts, because the problem may be completely different from what they tell us.

[Svetlana201]

Svetlana201, we don't have dishwasher repair specialists at all. Those who repair washing machines do not undertake dishwasher repairs.
I just had my third (the most unsuccessful) one, I had to buy a new one. The old one needs to be thrown away, but I don’t understand how to drain all the water out of it, so that it does not flow along the entrance and the weight without water is still less

Yelenochka Nikolaevna, unfortunately they are nowhere to be found.

Wow, girls!

[Elenochka Nikolaevna]

Elenochka Nikolaevna, Elena, the first thing I thought about. It's just a big towel, wring it dry ...

[lira3003]

lira3003When you open the car, there is no water, everything is dry. You start to move, leaks from under and from the drain hoses.
Somewhere inside there is water, maybe in the salt compartment. I tell my own people to pick it up and put it on something, let it flow down. Damn, there is nothing to bet.

icon that there is no water.

It looks like a pressure switch, although maybe the temperature sensor is covered. If the machine is more than 5 years old, there is a possibility that the control controller.

no dishwasher repair specialists.

strange, if there is a warranty service, they also carry out post-warranty repairs.

The car is 4 years old. Yesterday my husband pulled out and disassembled partially, today he will try to ring. I don’t know what will come of it.
By the way, she had water in the side wall. Why didn't it completely merge?

I report on the dishwasher, suddenly someone will come in handy. On the advice of one good person from another forum, my husband removed the ten, called the tester - it does not work. In addition, external signs of malfunction were visible on the heating element. We ordered a new one in the online store (4800 plus 400 delivery). Received and my husband assembled the car - WORKS!
In total, the repair cost 5200, they called the masters on the ads, they said that the whole thing would cost around 15 thousand

Received and my husband assembled the car - WORKS!

Golden husband! And hands from the right place !!! Congratulations
And what

external signs of malfunction were visible on the heating element.

??

Thank you!
When my husband unrolled the heating element (in my model it goes with a pump), he saw the place of burnout of the track and traces of soot on the plastic casing. These places on two parts coincided, that is, it became clear that the ten was burnt and left traces. Here is a photo

Well ... now my PMM broke down Siemens SR 64M001RU / 11
Begins to wash, and then stops and gives an error E 01.
The day before yesterday also stopped in the middle of the wash, without an error code. I thought that some kind of glitch had passed. Launched the program again, she executed it successfully. Now after the start it turns off after 10 minutes and writes an error code. It does not restart immediately, only after 20 minutes, but then stops again. Heats the water.
Brains, sensor?

[Sonadora]

Sonadora, Manyasha, namely E01 or E1? Your instructions should include what code means what

[V-tina]

V-tina, Tina, namely E 01. There is nothing in the instructions about this error. But, it seems, I have already found a fault - short circuit.
I barely pulled out the plug, so everything "stuck" there.



Then everything looks logical: heating begins, due to a short circuit in the outlet, the voltage drops, or maybe the PMM's brain senses that something is wrong, the protection is triggered and cuts everything in Fig.

But it seems that I have already found a fault - short circuit.
I barely pulled out the plug, so everything "stuck" there.

already easier, you can at least hope that the problem is not in the typewriter ..

already easier, you can at least hope that the problem is not in the typewriter ..

This is yes. The cost of repairs today ... In the evening, my husband will look. In the same outlet, next to it, and the washing machine turns on, but everything is fine there, it was PMM who was shorting it.

This bastard, who is muSh, mocks me at me. He says that all normal women can arrange nothing out of nothing: a scandal, salad and a hairdo, and his blonde wife also contrives, and systematically.When the lights suddenly went out in our hotel room, my husband was not at all surprised. I just asked what this time I included in the network.

and my dishwasher / hotpoint ariston / stopped in the middle of the program, the salt button blinks, add salt - it still blinks and no buttons react. constantly makes noise, like the pump is working, and it turns on itself, if you do not pull the cord out of the socket, turn it off, it turns on itself and so on in a circle. Has anyone come across this? what could this happen and how serious is this breakdown?

You need to check the sensor for water leaks. I had it. Condensation accumulated under it and the sensor did not allow the machine to work

[V-tina]

V-tina, Tina, thanks for the support. PMM works! So yes, it was all about the short circuit.

By the way, about the short circuit. LED lamps have already been knocked out twice with a 16 amp machine in the dashboard. It looks like they have a jamb in the electronic unit. A year later, they fail, they begin to warm up and everyone, hello, the world is ending at home.

It looks like they have a jamb in the electronic unit. A year later, they fail, begin to warm up and all-

don't scare me, we recently set ourselves something like that)

Tina, we switched to LED lamps a long time ago, but the problem arose only with Gauss lamps, not only the cartridge burned out, but the wiring to it had to be changed.

Gauss lamps

we have something else, thanks

[Khamar]

Khamar, I had something similar with a typewriter. I called a specialist. I recommended to fill the machine on the left side at 45 degrees, a glass of water should flow out. We did so and it worked again. it's a leak

I had something similar with a typewriter. I called a specialist. I recommended to fill the machine on the left side at 45 degrees, a glass of water should flow out. We did so and it worked again. it's a leak

what is the leak and where should the glass of water come from? from the hose? Do you need to disconnect it? sorry for the stupid questions. Before that, I had a completely simple domestic dishwasher, "Technosila", plowed for 10 years, if not more, there was not a single breakdown, but this one is only 2 years old and such an attack.

[Khamar]

Khamar, Olga, the problem described is similar to the operation of aquastop. Water somehow got into the sump of the machine and the aquastop shuts off the water supply.
You can, as you have written, push the machine and tilt it forward or sideways, water will flow out from below. But be careful, do not tilt too much, otherwise you will flood the electronics and run into expensive repairs, as happened here.
You can simply open the machine and give it a few days to dry naturally.
If after a few days the machine does not come to its senses - you will have to call the master - there may be too much water or it is leaking from somewhere. Or maybe that's not the problem at all.

There is no need to tilt anything, there are many different electronics ... Everything is much simpler, I myself found the problem and fixed it in 5 minutes, so don't worry. 1st pull out the machine so that you have access to the back wall, unscrew 4-6 bolts that hold it. 2nd get on your knees and at the very bottom, through a row of wires, look where the plastic tray is, in this plastic tray there is a movable float (aquastop sensor). 3rd, we take a roll of toilet paper, crumple the paper balls, so that it would be convenient to push through a not very large hole and soak all the water that is in this tray, there really is no more than half a glass, but you will exhaust a lot of paper)))). 4th we twist the back cover back, push the machine, use it with pleasure

[Byaka zakalyaka]

Byaka zakalyakaWhy does a weak woman need so much work. I offered the fastest repair option, which I tried myself. And then: spin it, spin it, get wet.
You do not need to unscrew any hoses.

thanks girls, I'll try, see what happens

Maybe someone came across such a problem. I have a narrow Beko, it works for 8 years.I start washing, the dishwasher draws water, the rocker arms do not start spinning, the machine hums slightly.

[zoyaaa]

zoyaaa, Electronics unit, circulation pump, service master call.

Alexander, thank you very much.

After working for 15.5 years, my PMM Electrolux ESF4151 broke down again, the 5th repair is obtained.This time, water leakage, aquastop did not work, the reason for this phenomenon was not found out, the autopsy showed that the drain pump snail cracked, plastic degradation and a crack formed. It was decided not to repair the PMM, during an external examination, I discovered the aging of the drain tube from the distributor to the drain pump, the machine would have lasted another year or two at most, it would have been necessary to change the distributor bowl with pipes.
I decided to change PMM to Electrolux ESL94655RO