Panasonic Bread Makers Problems and Breakdowns

It looks like it is. I do not remember the diagram, if the board is in order, then it remains to check the transformer for an open circuit.

The mistake came out with a stove. I wrote that I have 2501 and I have sd 257. There is no transformer here. I'll try to throw off the photo

Better circuit

Now my bucket drive has also collapsed, I will now disassemble and hope in sorrow. that only he is alone !!! Who knows where to buy lubricant, they have it 🔗

[Elena]

Elena, You can buy at the service center for the repair of copier printers, it is called lubricant for thermal films, ask for a small package of 2 ml you don't need anymore. Grease type for example
CK-0551 or Molykote HP-300 (made by Dow Corning) or, in extreme cases, PMS-200, can be found on the radio market.

Alexander thanks for the tip



Alexander wrote you a question in a personal, if possible, answer this before evening. Thank you

[sazalexter]

Guys, SOS! This morning my Panasonic SD-ZB2502 fell, the case cracked in two places


Do you think it needs to be repaired? While the HP was lying on the floor, it was still buzzing, then I turned it off, now I'm afraid to turn it on ...



sazalexter, please look at my unfortunate bread maker ..

The body is easy to treat. A fine metal mesh is superimposed on the place of breakage, melted into plastic with a soldering iron, more plastic can (and should) be melted on top. Experience has shown that I was not offered a single real glue in a special store. Although .... maybe I was out of luck ....
But you still have to turn it on. How else to know if she wants to work or not. Whether something burst inside or not ... Especially if there is a silumin inside.

[Ninelle]

NinelleLet's hope that only the body was damaged.

All plastic parts must be well glued / welded / ... to restore the original tightness as closely as possible, since the internal air space is important to maintain the temperature inside the bulb.

These parts can just as easily be replaced if there is a suitable option for a used stove for spare parts.

And in this situation, the metal case remained intact. It would be made of plastic - in general, everything could break.



And how it happened. why did you fall? If it buzzed, then probably during the batch.

And how it happened. why did you fall? If it buzzed, then probably during the batch.

During the kneading, she fell, she stood on the windowsill, has been standing in this place for a year, never fell, and then she collapsed ...
works while only turning on the pizza mode, spinning, and are these parts sold? Do not know?

The body is easy to treat. A fine metal mesh is superimposed on the place of breakage, melted into plastic with a soldering iron, more plastic can (and should) be melted on top. Experience has shown that I was not offered a single real glue in a special store. Although .... maybe I was out of luck ....
But you still have to turn it on. How else to know if she wants to work or not. Whether something burst inside or not ... Especially if there is a silumin inside.

Oh, buying a new one is like a Boeing wing.

[Ninelle]

Ninelle how I sympathize with you. I found a store in search of my part, but it is not verified, although the reviews seem to be quite good. There is a case, made of plastic SD-2500, SD-2501

🔗

SD-2511 and SD-P2001

🔗

you need to ask Alexander there is a difference in size and in the same place
top frame SD-2511

🔗

in the picture I looked 2512 metal is similar to 2511. and 2502 metal is similar to 2501 like

Oh, buying a new one is like a Boeing wing.

at a price of 4 thousand rubles + delivery - these are 2 parts, so it hurt me to buy a Panasonic blender knife at the price of the entire blender

[Ninelle]

NinelleThe part of the body that does not respond to bread and the work of HP is seemingly cracked, only visual perception, the only thing confusing is the crack in the HP leg, you can try to strengthen it from the inside with epoxylin or liquid plastic.

[Ninelle]

NinelleThe part of the body that does not respond to bread and the work of HP is seemingly cracked, only visual perception, the only thing confusing is the crack in the HP leg, you can try to strengthen it from the inside with epoxylin or liquid plastic.

Thank you, Alexander, do these parts change?

[Ninelle]

Ninelle. Yes, Nelya, these parts can be replaced.

In the topic of spare parts, Alexander gave a link to an online store. Here are the spare parts for your HP model, there is both an upper frame (no. 18) and a bottom (no. 52).

🔗




And about the fact that HP "threw itself" from the windowsill, after a year of "obedience": rather, the surface of the rubber feet is stained, at least for a year, dust and kitchen rubbish (crumbs, flour ...).
You need to periodically wipe / clean the feet with a damp cloth. to freshen the rubber and restore grip to prevent slipping.
If the stove begins to move during kneading, URGENTLY wipe the legs!
Be sure to check how stable / strong it is! Excess moisture can also slip.

URGENTLY wipe the legs!

... and remove from the windowsill. Choose a normal place for her, if there is something already there - rearrange it on the windowsill. And finally, window sills are not intended for this.

And about the fact that HP "threw itself" from the windowsill, after a year of "obedience": rather, the surface of the rubber feet is stained, at least for a year, dust and kitchen rubbish (crumbs, flour ...).
You need to periodically wipe / clean the feet with a damp cloth. to freshen the rubber and restore grip to prevent slipping.
If the stove begins to move during kneading, URGENTLY wipe the legs!
Be sure to check how stable / strong it is! Excess moisture can also slip.

Natalia well, do I really look like a woman who hasn't wiped the dust for years
The reason is different, the apartment was bought with a municipal renovation and we are not finishing it yet, because we are engaged in sealing joints, replacing heating, windows, everything that the developer did badly, electricity, including, does not belong to the ideal work of the developer, so I have everything on extension cords, everywhere, as in the army headquarters of the Second World War, the wires and on the eve of the husband just disconnected and reconnected the extension cord, apparently moved.

[Ninelle]

This is another matter. So the circumstances were.
Ninelle, I scored in the search engine "I sell panasonic bread maker for spare parts" and found ... Everything that cracked in yours is whole. Issue price 2000 r. I did not look further, there are many offers.

[Ninelle]

Ninelle, girls, too much chirping and panic.
We do not yet know what is damaged besides the case. Does it work.
Let's decide without any advice first. And then the inconsolable girl has already begun to load with service centers !!!
Virgin, cool it down.
What's not spinning and not heating up there !?

Yes, everything is spinning and heating there. And the main thing is that the board was not damaged once the pizza mode started. I would start a little loaf.

[Wit]

Wit, well, by God!
Well, what are you doing?

Natalia well, do I really look like a woman who hasn't wiped the dust for years

Nelichka, I never meant it. I didn't want to offend or reproach. I wanted to help so that this would not happen again.
My HP stands on the countertop sideways and only 4 cm from the edge, instead of the 10 cm laid down according to the instructions.I don't even wipe it every week under the bread maker, but when I wipe it, both the countertop and the HP legs are from below.

Sori

For what? What did you write above yourself? But I would definitely not recommend fusing the mesh

So that's what we're talking about!
Why panic!

Natasha, Ninel is just upset. Ah, what you wrote (and I, by the way) will be sooo useful for others, lovers of window sills (Ninel is not concerned).

Why panic!

And there is no panic. And people give different advice and solve the problem. Ninel herself will choose what suits her. Fortunately, there is plenty to choose from

[Wit]

Witif there are guaranteed options, others. - I wouldn't do it either ... I was talking about that. that I didn't have to find others if I read carefully ...

Ninel herself will choose what suits her. Fortunately, there is plenty to choose from

I just wanted to talk about it. But the "help from the audience" is not always adequate. A specific question, but here it is advised to wash the footpegs ...

But the "help from the audience" is not always adequate. A specific question, but here it is advised to wash the footpegs ...

The advice about the legs was given as the simplest minimum so that the repaired HP does not fall again, at the very first use.

Valentine, nevertheless you do not read carefully or do not delve into it. Natasha wrote everything correctly! And not just for Ninel.

I was not offended by anyone, I am grateful to everyone for their help, I want to start it myself, but with a cracked leg I am afraid. It's a shame, Pan Panas served with faith and truth for almost four years, and now they did not save it ... In my old apartment, my tabletop was close to the window sill, and it was just below the table top and the bread maker fit into the window sill to a millimeter, and was, as it were, pressed by the table top ... And then I put it - it's worth it, well, okay, I think, before the repair ...
Tomorrow morning I'll start a quick bread, although I have bread due to the breakdown of the HP, like a fool of a makhorka. In the morning I bought a baguette at the bakery, my mother bought a ciabat, Maska and I baked two breads in the oven, my husband will definitely bring in a thread ...



Somewhat clumsy, but the main baker is only 6 years old

[Ninelle]

Ninelle, and on Avito on my link did not go? Only 2000 for a breakthrough of spare parts! I suppose the subway is nearby.

[Wit]

Wit, already went and wrote to him
Waiting for an answer

Good!

[Ninelle]

Ninelle, and on Avito on my link did not go? Only 2000 for a breakthrough of spare parts! I suppose the subway is nearby.

The owner of HP replied, he has already sold these parts.

I'll look again, the master who repaired the PMM promised me at the warehouse to look at my parts.

Guys, I bought a Panasonic 2510 today. And that's what confuses me - the mixer does not sit tight, but with a rather large gap. In my old oven, it sat moderately and not tight and did not dangle. And then it just dangles. Is this normal for Panasonic?

[switlle]

switlle, yes, she hangs out. It should be so. For Panasikov.

[switlle]

switlle, yes, she hangs out. It should be so. For Panasikov.

Huh! Thank you! You saved my day. And then I was depressed).

As a result of this "chatter", the batch starts without a jerk, for the full pleasure of the engine

At first I thought so. But when she began to knead, there was a fear - but whether it would cling to the bottom and ruin the Teflon coating. But I think it's missing because of the linings.

Exactly.

[The blade shaft creaks in the bushing]

Tell me if there are any subtleties in the installation of the bucket drive pulley? : girl-th: Collected SI-350 grease, the part from the Bucket site is now installed a little unevenly. The empty bucket runs silently. It began to creak like this, baked bread strictly according to the recipe. The video is not mine, but the sound is like this.

Comments read- The blade shaft creaks in the bushing how to lubricate? I'm afraid to disassemble the bucket, what if it starts to leak?

I also thought for a long time that the shaft was creaking, but I still tried to lubricate the parts on the bucket with ordinary vegetable oil (just a little), which are in contact with the counterparts on the HP itself (black, plastic) - the creak disappeared. Try it.

wait ... sunflower oil is not nearly as harmless as it seems. It can soften some materials unplanned. I would be afraid to lubricate my stove without consulting our boys.
Let our connoisseurs better advise a precisely tested lubricant or allow the oil

[Elena]

Elena, Did you change the assembly, or just the pulley? If assembled, the bucket may creak in the lock slot. We'll have to put up or rub with a pencil lead from a pencil parts of the contact between the bucket and the lock. Alternatively, try to turn the belt in HP, perhaps it was installed a little differently, so a creak is possible, I had such an effect, it passed after a couple of months. I would not grease with sunflower oil, it polymerizes quickly, the effect can be unpredictable.
Shl check if the shaft with the spatula turns easily by hand, after pulling the bucket out of the HP

Alexander only a pulley. I smeared a bucket of SI-350 now some kind of shuffling (I threw off the video for you) and the bucket became a little crooked. (I changed it by 180 degrees and still not exactly) There is a backlash when kneading. It's really strange, everything seems to be tightened and parts are native.And how to adjust the pulley to make the bucket smoother?

Shl check if the shaft with the spatula turns easily by hand, after pulling the bucket out of the HP

in general it is easy and with an empty bucket it is easy and quiet !!

[Elena]

ElenaIf, when changing the pulley, the unit itself was unscrewed, check that it was installed correctly, try to unfold it.
The black pulley is not adjustable.

I read that the pulley may squeak for a while and this is not a breakdown. In some manual

Alternatively, try turning the belt in HP, perhaps it was installed a little differently, so a creak is possible, I had such an effect, it passed after a couple of months.

And somewhere else I read about scree and there pointed a finger at a pulley. They say he can creak new for a while. And let yourself squeak, the yeast will not go deaf.

And let yourself creak yeast will not deafen

Exactly!
We have a topic about the creak of a bread machine and there is a description of several reasons. But like talking about a bucket.

Kneading creaks and bucket problems

Duc belt after all is not visible and think that the bucket creaks. Lan, I'll take a look, and you take a look in the manual.

Squeaky kneading and bucket problems # 30

I will even quote from there

Of course the belt creaks when slipping on the pulleys due to the heavy load. And it turns out that when you overdid it with flour or did not add a little water - the dough turned out to be too thick. The solution is simple - immediately add a teaspoon of water (or a little more) to the container, the creak will stop almost immediately. Well, in general, of course, it is better to try to prevent this - engine overload and increased belt wear are not good.