vnenaev
Greetings to all. Also faced with the replacement of the oil seal.

Quote: sid2857
Finished products (fluoroelastomer, silicone and fluoroplastic)
I am going to the same company, which material is better to order the oil seal, so that it is food grade. You have used profile R04,
why him?
sid2857
Quote: vnenaev
You used the R04 profile, why exactly this?

Repair bucket Moulinex OW 5002

1. This profile suited me. It works both as an oil seal and as an additional bearing.
2. I still have fluoroelastomer.

I will quote the info from the Rost site.


One of the main areas of activity of GK "Rost" is the production and supply of O-rings made of fluorine rubber FPM, the dimensions of which correspond to GOST 9833, as well as imported standard sizes.
FPM is an improved analog of Group 6 rubber (IRP-1287). It is a fluoride rubber known for its sufficient durability, non-combustibility, as well as resistance to critical high temperatures.

Application area

Our assortment includes different types of rings suitable for use in food industry, pharmaceutical, for gas equipment and gas supply systems, steam and hot water resistant, to oils and mineral greases, as well as during vacuum use

Good luck!
vnenaev
Quote: sid2857
This profile was fine for me
The profile is clear. And another question: if I have a shaft size of 8.3 and a seating for an oil seal 20.1, when ordering these figures for me
and twist or round to whole numbers?

Quote: sid2857
use in the food industry
That is to say, to make FPM from fluorocarbon rubber for the food industry.
sid2857
I recommend taking a bucket with you, it's safer (planting in place).
vnenaev
Quote: sid2857
Recommend
Thanks for the quick reply, after the weekend I will go to order.
vnenaev
They also carved an oil seal for me on Govorov. For those who travel, of course, you need to know what to order (many unnecessary questions). Of the "food" materials, there was only silicone and fluoroplastic. Price 150 plus 50 for speed
Ilmirushka
Dear owners of HP, and repairmen of all kinds of oil seals, bushings and other differences, I do not understand anything about these subtle matters of turning production. But I see that in the bucket of my HP, that PIN, on which the spinner for kneading the dough sits, in its nest IS NOT VERY TIGHT, that is, IT is staggering, and WALKING decently. Because of this, the bucket began to leak. And these are not all problems with my HB. From below, not just water from the bucket flows out of this structure, but it gets wet with something black and, as it were, oily, it is washed off with difficulty. I thought it was carbon deposits, and when I tried to wash it, I realized that it was something there, as it were, melted, well, or so much worn out, worn out. How and where to repair all this, I do not know. Experts and simply versed people, tell me if it is possible to order a new bucket for DELTA-78B HP, or maybe a bucket from some other HP will fit this HP, which can be ordered and bought without any problems. HELP!!!
Florichka
And my pin had already fallen out and in general everything fell apart. HP Kenwood 450. And the bucket is inserted into the HP case and there were 2 small rectangles, one broke off. So I think I'll spend 3500 on a new bucket, but it won't work. I don’t understand your clever talk, this is not for average minds. I don’t want to buy a new one, I bought my own for 9. Straight grief.
romchik528
Quote: vanex

Uraaaaaa !!!! Finally, I repaired my Mulya =)))) Dear members of the forum, and even more Murmansk and residents of the Murmansk region, I finally found where you can make a fluoroplastic sleeve (instead of an oil seal) for our bakery. So who needs it - contact !!! Issue price 400 rubles for two bushings. But first things first.
1) I decided on the type of repair thanks to the forum - it was necessary to replace the oil seal.
2) I decided, again based on the experience of the members of the forum, that I would remove the oil seal by drilling the rivets and completely disassembling the unit with the rivets in place when assembling stainless screws.
3) I started drilling - everything turned out to be quite simple: a drill, a drill with a diameter less than the rivet itself and accuracy.
4) It turned out a separate bucket and ...

... other parts: frame with shaft and bearing assemblies.
Hello everyone, guys, this is the situation, the shaft dangles in the bucket body,
very strong backlash, tell me there is a bushing in the case, does it change?
Or what can you think of?
sazalexter
romchik528, The whole topic is devoted to this repair, read from the beginning.
romchik528
I read, but did not find anything for the bushing, whether it is there or not, only the oil seals are in question and how to replace it!
seemingly a part like a cast Bread Maker Moulinex OW 5004 bearings are also not there.
ancifer
Greetings, friends! I also have an OW 5002 stove model.
I disassembled the bucket, or rather pressed out the bushing and picked out the remnants of the oil seal. The reason is leakage, backlash.
I found shops on the internet where you can buy oil seals and bushings, but the trouble is, there are a lot of sizes, the choice is huge, how to determine which standard goes to my bucket? I don't have a caliper, and I don't have any friends either. How to buy and not miscalculate? What are the dimensions of the gland and bucket bushing for this oven?
Vova1330
tried everything. The best option is to grind a fluoroplastic bushing instead of a bearing and an oil seal, my size is 22x8x14. outdoor diameter by press. landing int. on the slide. all for a few years without replacement
madgf
Hello everyone. I don't know if the topic is still alive. I have an important question, what kind of sealant to seal the assembly during assembly? From the factory it was glued with some kind of sealant, of course I cleaned everything, repaired the unit now it's time to assemble. Do you need a special food grade sealant or you can pile on a regular heat-resistant one ..
Fat_Rat
Hi, the shaft that is already inside, not in the bucket, is jammed in the bread maker, disassembled, washed, rotates, tell me, can it be lubricated with any grease or some special food grade? He does not come into contact with food ...
sazalexter
Fat_Rat, Grease Molykote HP-300, or CK-0551 above in the topic discussed.
dfgdfgw
Hello everyone. The bucket of the supra bms-350 bread maker broke. Can I replace the bucket with another manufacturer and where can I buy a bucket for this bread maker?
gbrik
Hello!
did you manage to repair the bucket for 600230?
i have exactly the same problem ...
however, the stove is already seven years old.
I’m thinking, buy a new bucket for 1600, is it time to buy a new oven or try to repair it?
can you correctly name the parts that need to be replaced, that you changed?
ramozz
Quote: vanex

13) I put the screws into the holes left after the rivets and tightened them with nuts.
Ivan, hello. And the screw heads themselves were not sealed from the inside of the bucket? Are they pulled dry and does not leak?
Palych
today the shaft (the pin on which the blade is held) fell out of the bucket! In my opinion, it is the spring washer under the rubber gland, on which the shaft is held, ground off or broken.
I see this is the main problem for many.
It can be quickly and inexpensively solved with ordinary rubber sanitary washers, gaskets for old taps. That is what I did in early spring and so far "the flight is normal." No disassembly, cutting of studs, drilling, turning and PTFE. I think women can handle it even better than men.

All recipes

© Mcooker: best recipes.

map of site

We advise you to read:

Selection and operation of bread makers