Dishwasher malfunctions

I have been using the machine for a week, but the salt shortage indicator is constantly on.

In some machines, it goes out after several washes. Is this really an indicator of a lack of salt? An icon that looks like "S" or "*"?

And yet, yesterday after washing, almost all the powder remained in place - it just turned into a large lump.

Most often this happens if you pour the powder into a WET dispenser and set the delay start timer. At the beginning of the sink, there will be a stone.
I always leave the detergent drawer open so that it dries completely before the next wash. And I fall asleep the powder BEFORE I start loading the dishes. Then the water flowing from the plates is not scary ...

[Jefry]

Jefry thank you for quick answer! I understood everything about the powder - I really put on the timer. And the icon that looks like a spoon is lit, I have an Electrolux. I looked again at the instructions - like salt. I turn on the machine and this indicator comes on. The instructions say that it can burn for several hours after the first boot, but I've already had a week of daily use.

Hi Hi. I have such a problem. I put the Finish pill and the program for 30 minutes of tamping, after the end of the cycle, half a pill at the bottom of the machine. There was no such thing before. The car BOSCH SRS 46 T 42 EU is only a month old.

Well, in general, they do not recommend using tablets for short programs, and the instructions say about it. They are designed for a standard "long" program. Although many ignore this rule. And in your particular case, it looks like the work of an aquasensor, or there was less water, or it was colder, or the operating time of the pump was less than in those times when the tablet had time to dissolve. There may also be different pills - "left" and "right". In ordinary typewriters, the location of the dishes and the place where the pill gets to also affect the dissolution process, but your PMM should have a special pocket on the upper basket. Bosch gives it as a separate chip.
In general, this is not fatal ...

[Nataly_rz]

Nataly_rz Your salt is burning, you need to fill it up to the top, while the water comes out, this is normal. I don’t remember how I can fit a pack of salt. I add very rarely.

[GalinkaMalinka]

GalinkaMalinka Use separate products! Pills are like fast food, long and long there is use is more expensive

[sazalexter]

Oh thanks sazalexter, finally waited for an answer. Salt is still burning with me. I tried to fill up several times, the water comes out, and I was afraid to pour further ... So, you need it despite? Then I'll do it

[sazalexter]

Thank you sazalexter and tell me which ones do you use?

[Nataly_rz]

Nataly_rz Forgive me for a long time, for a long time I have not looked into this topic, although all this time on the forum. Knock in a personal if anything And then with these devices, kitchen ones at all
Now the machine is "under the tail"

[GalinkaMalinka]

GalinkaMalinka Finish and Somat, absolutely no difference (Sneakers and tomatoes will fly right now)

[Luysia]

Luysia For prevention, you need to use specials. liquid for cleaning PMM.
DO NOT use tablets, and DO NOT save on dishwashing powder

Please tell me which liquid is better to buy for cleaning PMM.

Please tell me which liquid is better to buy for cleaning PMM.

Anyone, they are the same, I like Finish and Electrolux

I wrote here about the pill that was not broken at the bottom of the PMM. So I report and say thank you to everyone for the advice. I bought Domol powder in DC and everything is fine, I like how it copes with the dishes in 30 minutes and there is no smell from the dishes, and there is no pill residue. And what would I do without you all? !!!!!

Tell me what it can be - Dishwasher "Bosch" SGS 44E02 constantly fills and immediately drains the cart, fills and drains ... and so - ad infinitum ... About 2 months. this already happened back, they called the master - he said that there was no breakdown, but it was simply not connected correctly (the drain hose was lowered). After his visit, she turned on herself, and now she again refuses to wash. What could it be? The sink is only 1.5 years old.

Good day!
Please help with advice. I have a BOSCH machine. For about 6 months already. Everything was fine, but the last 2 days the auto shutdown did not work. That is, the program ends, it beeps 4 times and then a minute later it had to beep one more time and disconnect from the network. And now, five minutes after the squeak about the end of the program, it starts beeping again 4 times, but it does not disconnect from the network.

Help with advice, yesterday there was an accident with the washing machine, our drain was made into the sink, apparently the drain was bent back, and I did not check it at startup, in general, the water spilled onto the countertops, the floor ..., they saw, stopped the program, removed all the water, then finished washing program, after that I loaded the dishwasher and turned it on, for some reason she immediately chose the program and began to make noise with the door open, as if the program had been interrupted, but the display was on that the program had not started yet, I closed the door, appeared noise, as if water was being collected, then a buzzing, after a few minutes I opened the door on the display, the lack of water sensor was on, the dishwasher was turned off, then turned on again, it still buzzes, as if trying to immediately draw water ... maybe the control unit was poured ?? ? when did the water pour from the washer? left for the night, in the morning nothing has changed ... the dishwasher and 3 months away, I really do not want to be covered ..... advise where to check what ?? dishwasher BOSCH, 45 cm

Maybe she's trying to drain the water, not draw? It seems that the Bosches have such a reaction to the triggering of the aquastop sensor. Apparently water got into the sump. The treatment is simple - either wait until it dries on its own in a couple of weeks, or pull out the machine and tilt it forward to drain.

Thanks to Jefry for the promptness and advice, let's try to check the availability of water)

bosh silens plus 3in1 a high-pitched squeak is heard when washing. a little annoying. before that it was not heard at all. is it a harbinger of breakage? and can you do it yourself?

Who is our doctor?
The rinse aid button stopped lighting up. The salt ignites, but the mouthwash does not. I used to catch fire in 3-4 weeks, now it doesn’t light up for a month or more ... Until I see myself that it’s time to pour. What is it, where is it jammed?

[RybkA]

RybkA It is not clogged, it is a problem with the rinse aid sensor or indicator (which is less common) What type of machine?

Ariston's typewriter will not tell the exact model now, but if it is important I can search.

[RybkA]

What should I do if the rinse aid indicator is constantly on? Although the rinse aid itself is poured, as described in the instructions, not a little and not to the brim.

The rinse aid button has stopped lighting up

RybkA, dear! where have we sinned like that ...

Does Well know him? I don't bother too much, well, it doesn't burn and joke with her! The main thing is that the soap is good! When I see that "dew" remains on the walls of the door, I immediately add it and everything is fine again. There are cars without an indication - people somehow live ?!

[RybkA, IRR]

RybkA, IRR I have a thought that you use one rinse aid. The sensor of the rinse aid is optical (optocoupler with an open channel), i.e. it checks the level by refraction of the medium. So maybe it's the rinse aid?

[sazalexter]

sazalexter
nope, hardly. I also just went out at some point the indicator of lack of rinse aid, and I use different ones (finish, iplon, now - top house) ... I don't know what can get clogged there or not, but purely because of this, I'm too lazy with the service to contact.In appearance, it seems - nothing special is visible, the funnel is small in a compartment with a maximum pattern. Drains into the compartment normally
, washes - too (well, that is, the dishes are dry normally) ... I follow myself in the end, I top up every couple of weeks. I have a Boshik desktop, 50th.

[RybkA, IRR]

RybkA, IRR I have a thought that you use one rinse aid. The sensor of the rinse aid is optical (optocoupler with an open channel), i.e. it checks the level by refraction of the medium. So maybe it's the rinse aid?

I have a finish

[IRR]

IRR Remind me how long ago you purchased PMM?

Sasha, I'm certainly off topic, but since you're here, I'll quickly ask you while Irka washes the floors. I just washed the stove, and my lighter began to click on its own ... well, which one is near the burner .. stands, you know, a clean stove and I click all in disheveled feelings .. I broke something there, right?

[IRR]

IRR Remind me how long ago you purchased PMM?

2-3 weeks ago (asho such officialdom? We have been for a long time: drinks: and) or in this thread so nada?

I don’t know what can be jammed there or not, but purely because of this, I’m too lazy to contact the service. In appearance, it seems - nothing special is visible, the funnel is small in a compartment with a maximum pattern. Drains into the compartment normally
, washes - too (well, that is, the dishes are dry normally) ... I follow myself in the end, I top up every couple of weeks.

Well, that's exactly my situation!
It has been off for exactly half a year, the typewriter is a little over a year old. At first I used Finish for a long time, in fact, only two months ago I switched to Domol.

Sasha, I'm certainly off topic, but since you're here, I'll quickly ask you while Irka washes the floors. I just washed the stove, and my lighter began to click on its own ... well, which one is near the burner .. stands, you know, a clean stove and I click all in disheveled feelings .. I broke something there, right?

I don't know this, I can assume that the button has sunk or liquid has got under it

2-3 weeks ago (asho such officialdom? We have been for a long time: drinks: and) or in this thread so nada?

Sorry, this is making me crazy, and somehow I'm not used to it differently. Don't be angry

There was an idea to rinse the rinse aid hopper with water, but how to implement it? Maybe with a syringe?

most likely I filled this lighter with water, it clicked often at first, then less often .. then even less often .. now it does not click, probably dried out

There was an idea to rinse the rinse aid hopper with water, but how to implement it? Maybe with a syringe?

There, pressure would be necessary then, and not pressure with a syringe, but so ... plus then it will not work out ... the light there should work for the presence of liquid or for a certain composition of it (as is the case with the conductivity salt indicator, afair )?

[Ernimel]

Ernimel As already reported there, an open-channel optocoupler works to change the refractive medium. From experience, such elements fail but rarely.

[Ernimel]

Ernimel As already reported there, an open-channel optocoupler works to change the refractive medium. From experience, such elements fail but rarely.

if it's about my breakdown, then she called the master. Let me tell you what it was.

refractive medium change

especially for the humanities mona to explain a little bit? If I put it down somehow, wash it out, and there will be water (and it will remain, it doesn't matter where it can go anyway) - will the sensor work for the absence or presence of rinse aid? According to my logic - for the presence, and, therefore, I still do not know whether it has worked or not (the light will be extinguished until all the liquid has been pumped out), right? If I knew how to drain the liquid from there, I would even try to drip some kind of luxus for the bathroom. How else to wash it out later? ..

[Ernimel]

Ernimel Better still contact the service

[IRR]

IRR so what happened to the typewriter?

Your regiment has arrived.
Thanks to the information received on your forum, I became the owner of CENTURY 6530. And now I've been dabbling for a whole week. Even before the purchase, I sat on the forum for a couple of weeks and read about all sorts of nuances, and therefore, during the first operation, I did everything (as it seems to me correctly): I poured water, poured salt, poured rinse aid (100 ml was included) and use detergent powder. All Kolgonit. I drove in all modes. I'm happy. But today the car baffled me. I loaded the dishes (not very dirty) and put them on auto mode. She washed it for 1 hour and 20 minutes. I open it, there is foam below.I was surprised because I am pouring less detergent powder than the norm. The dishes are dry. After half an hour, I started an express wash (30 minutes) without powder (I decided to just wash off the foam). Before that, I cleaned the filter. The foam is twice as much. WHAT IS IT LIKE
I remember someone on the forum already faced a similar problem, but I do not remember how it was solved.
Can you share your thoughts

The foam is twice as much. WHAT IS IT LIKE
I remember someone on the forum already faced a similar problem, but I do not remember how it was solved.

Is the consumption of rinse aid too high? He's foaming. Or, m. B. consumption is normal, but something is wrong with it (substandard). It also foams, it happens, in the presence of protein contamination (eggs, milk, etc.), but after the second cycle it is clearly not it ... I would think about a rinse aid for sure.

Hello everybody!
I am in sadness, recently purchased PMM BOSCH SPV 40 E 20 EU and already at the first wash an unpleasant moment was discovered.
Almost immediately after the start of the program (after 30-40 seconds), an unpleasant rattling sound appears, very similar to the sound of a working electric shaver or a hair clipper. Lasts less than a minute, then a standard acoustic set of sounds, like a washing machine.
In the process of working through the entire program, the sound appears several times for the same short time.
I tried to press the walls, door, etc. with my hands. It does not help.
The dishes were washed normally. Are there any options other than calling a service technician?

Hello everybody!
I am in sadness, recently purchased PMM BOSCH SPV 40 E 20 EU and already at the first wash an unpleasant moment was discovered.

This is the sound of the drain pump running. It is quite normal for machines that cost less than a thousand dollars.

This is the sound of the drain pump running. It is quite normal for machines that cost less than a thousand dollars.

I am confused by the fact that friends and acquaintances do not seem to have such a sound, at least no one remembered.

I am confused by the fact that friends and acquaintances do not seem to have such a sound, at least no one remembered.

Drain and drain, several times per cycle. At the beginning, after rinsing the first and then several more times per cycle, the last time - when draining condensate after drying at the very end. I also have a Boshik desktop. The parents have a deluxe floor 45 cm, the built-in also drains, but there due to the fact that it is almost inaudible on the floor and in the closet. And Boshik squishes, yes. But what a thrill from the results!

there is an unpleasant rattling sound, very similar to the sound of a working electric shaver or hair clipper. Lasts less than a minute, then a standard acoustic set of sounds, like a washing machine.
.... Are there any options other than calling a service technician?

It doesn’t look like a drain, it immediately appears. But the drain hose should be double-checked so that it is not pinched. So is the water set hose.
Check the stacking of dishes, whether the blades rotate freely.
If it doesn't help, I would call the master.

Difficult to diagnose just by the sound description. When the pump is running (and it almost always works at the beginning of the cycle to remove water that could remain in the machine), the PM vibrates. Is the dishwasher leaning against anything? I have such sounds when something is standing on the PM or something is leaning against it.

It is the same (the specified model) installation How can you lean there?