Vacuum packing machine

For a long time I had a gochu 470, I ordered it myself from Korea, the quality is not bad, I liked the adjustable clips for the film, but I did not like the width of the seam! When packing fresh fish or meat, it will solder a strip of less than 1 mm, respectively, the seam is unsticked and there is no vacuum! I spat on this business and ordered, on the advice of fishermen friends, also a Korean eiffel foodmate, this is a completely different matter, the seam is wide, there is a moisture separator and all the necessary modes, I have been using it for a long time and everything is very comfortable. And recently I took a sous view of a thermostat, and now I am spoiling my family with molecular cuisine

And my sadness Dropped Redmond, he hit the table hard and got a concussion. There is no mechanical damage, but it stopped soldering after pumping out. Sucks until you forcefully stop it. Separately, the sealing button works. And if you press the seal immediately from the pumping mode, it instantly lets in air and seals it. The bag is full of air. The warranty is over, I suppose they will take decently for the repairs now. I wonder if it's even curable? It's a pity, dear, I have it and I need it

Shouldn't be very expensive! With academic interest, I disassembled my apparatus, and so there is a pressure sensor on it, which is responsible for automatically stopping the compressor. It could just fly off the wires from the blow, take it to the service, in any case, this little detail should not cost a lot of money ...

Girls, boys! No one has tried changing the sealing tape. I have small pimples on it, and when sealed in this place, holes are obtained on the seam. Buy a new one right away or is it possible to somehow overcome it?

So far, not a single bag has come apart, the seam, although thin, is very strong. But after the proficuka, the packages are unstuck even after several soldering, although the seam there is 2 times wider.

Girls, boys! No one has tried changing the sealing tape. I have small pimples on it, and when sealed in this place, holes are obtained on the seam. Buy a new one right away or is it possible to somehow overcome it?

In packaging stores, repair kits for impulse sealers should be sold, you can pick up the Teflon tape by size, remove the old one and put on a new one. But only this should be done by a specialist ...

I have the same bullshit without any blow - the air is sucked out, but the seal does not turn on. I press the button myself, the air immediately returns to the package, then it is sealed with it. Packages float - I press down with a plate.

[Yuri]

Yuri, thanks, so there is hope
Anna, did you try to disassemble or repair?

Anna, did you try to disassemble or repair?

Nope.

I press the button myself, the air immediately returns to the package, then it is sealed with it.

In all cases, without exception, and on any packages? It's just that it happens very rarely for me, now I think, what to sin on, the wrong laying of the wrong package or similar glitches? I was inclined towards the first option, because some movement and re-inclusion corrected the situation, and now I don't know what to think. ((

Now I was driving my packer again. He, apparently, was frightened of the repair and pumped out three test packages with a seal. What is this? I would have brought it to the service, they would have taken it for diagnostics and for non-existent repairs But, one way or another, the harbingers are bad ... At the right time, the device can fail.

In all cases, without exception, and on any packages?

Yes.

Hello, dear forum users! Thank you very much for this thread.My husband gave the task to buy a vacuum cleaner, I read you for almost 2 weeks (my baby did not give a lot of free time). I chose Sigmund. How to buy, I will be happy) Have a nice day!

Greetings to all!
I have a problem (((after 3-4 days the packages are clearly letting in air ... Caso. The seams seem to be intact ... No one came across?

[Natalia]

Natalia, I have a similar story. I put it in the freezer - there is a vacuum, and when I take it out - there is no vacuum. This is not always the case, but my packages are different. I sinned against the packer, but did not think about the bags. I'll have to see which packages are weird.

I'm sorry, there is no way to go over the whole topic. A very urgent question. Are packers with aliexpress worth considering? Today there seems to be a good discount. Anyone who has experience in using these vacuum equipment, please respond.

[notka_notka]

notka_notka, Natasha, a friend ordered from me there, it seems satisfied

I read that they had already begun to spit from the vacuumizers with Ali, and at first they squeaked with joy.

Oh, girls, I don’t know what to do. My Redmond works every other time after the fall. I don’t want to take it for repairs, because they will turn it on, but it works and will not bother, but they will certainly rip off the money. I can't even figure out why it works like that. Once I pumped out everything and sealed it up (everything that was at hand on the kitchen table - jars, bottles, spoons, etc.). And when a few days later it was necessary to evacuate the cheese, he flatly refused to switch from the pumping mode to the sealing mode. I threw this business, after a couple of days I pumped everything out and sealed it. Some kind of kapets !!!
Oh, I don't know if I need this Chinese man with Ali ??? The one that is white and pink and is magnetised to the refrigerator like

Oops, and I have the same garbage happened to the rather expensive MAGIC VAC® Genius, it pumps out, but does not go into the sealing mode. It is necessary to send to Moscow for repairs, I already bought a box. I talked with the master on the phone, conducted a couple of tests with him and he said that the sensor of sufficient pressure was most likely out of order, the device is maintainable and not expensive, since all parts are available, so I hope to keep within 2-3 thousand
That's just the question arises .. what expensive buy, what is relatively expensive, what about Ali ... one garbage

[Lena]

Lena, I also think so. I regretted that I had bought an expensive Redmond, banks are generally unclaimed.

The girls I have is Steba, in it you can forcibly solder and solder without pumping air, in principle, that's why I took it because there are such functions.

I have a CASO VC 150. Everything was fine, but not for long. With the modes, everything is fine, maybe by myself, you can forcibly turn on the sealing, there is a mode for wet products. He just began to make holes at the seams in places, solder through. Now it is under repair, it was not possible to fix it right away, it will be necessary to install a new sealing strip, it is not available now, whether it will be or not is not known. I'm waiting. At the same time, I began to read the topic again, slowly picking up a replacement.
The workshop is the only one in the whole city, which at least agreed to try to fix it. Others were immediately refused - there are no spare parts, the company does not supply. T. about. we have a disposable device for a lot of money.

[Buttercup]

Buttercup, the Redmond 21st model has all these functions and a hose and cans .... But, he hit me well on the table and got a concussion. So these functions are now useless.
When you forcibly press the seal, part of the air returns to the bag. This is not what is required of the instrument.



Girls, I ordered. I hope I'm lucky with the device.

And also a set of film in rolls, the price seemed attractive to me) Suddenly who needs it? Prod one.

Delivery from Russia, as promised. I will believe, what if the order really comes quickly
I have orders with Aliexpress for several months)

When you forcibly press the seal, some of the air returns to the bag.

Oh, it's a shame, is there still a guarantee? I have two evacuators, one "big" Shteba, and the other a small pistol Kitforth. But for kitfort you need special bags with a valve.In general, it's better for me to have two at once, you never know what happens to one

[by chance]

and another little Kitforth pistol.

Oh, now I was looking at someone who looked like Ali and thought - and he by chance not suitable for pumping out of cans under Wax lids?

[Lena]

Lena, the gun is cacique, but it pumps out. It is necessary to look at the size of the sucker.

[Bijou]

BijouI don't know, I don't have such Wax

[LisaNeAlisa]

LisaNeAlisa, wow .. Maybe I need it too?)) It’s been lying around in my bookmarks for a long time, but 2300 is a pity. And Ali has something similar for 1300.)

Bijou, I don't know, I don't have such Wax

And I have.)) A pump is also possible, but it's lazy if there is a motor nearby.

[Natalia]

Girls, I ordered.

Natalia, there is a video of this vacuum on youtube, the owner says that it works fine only with dry products.

[Bijou]

Bijou, although I have a hose from a goch, but it is more convenient with a pistol, always at hand, there is no need to collect. With a hose and a large evacuator, only bulk packages.

I studied for a long time and chose Sigmund and I really like him !!!! There are modes for soft and hard, for dry and wet foods. There is a manual mode. I didn’t regret it, although I didn’t initially plan to spend that amount for a packer. It was a gift!

[lesla]

lesla, Elena, congratulations, cute, let him continue to please with his work

[lesla]

lesla, Elena! What a cool car! Let it serve for a long time to the delight of the hostess!

Oh, girls, you experience such torment when there is a choice of technology! How much information I have re-read, and all our pages! And here it is happiness - the sigmund is in my hands and this is exactly what I wanted. By the way, the container is of course small, it can hold 500 grams of meat. This is enough for three for a side dish. We had enough.

Ladies, what about the Caso VC 11? In mvideo, bonuses are on, you don't want to dear. Is it worth looking at him at all?

[Mandraik Ludmila]

Mandraik Ludmila, I have two vacuum sealers: one Rrofi-Cook with all functions and packages, and rolls, the other Caso 20 pistol. Pro-Cook is a great thing, but I rarely use it when I need to send a large piece of meat to the freezer or marinate meat for Sous-Vid. As for Caso-20, at first nothing seemed to work, but over time she began to notice that the vacuum did not persist already on the third day. It seems that I'm taking a new package, but still something is wrong! I began to look for a replacement for him and found a Kitfort pistol on Ozone and the price for it was humane. The set included bags of different sizes and 2 lids. I tried it at work on the same day. I was satisfied, especially with the covers. Vacuumized sliced ​​ham, sausages, and much more. I made lightly salted cucumbers according to the recipe from the attached book, pickled the tomatoes in a jar under a vacuum lid, everything is just super! I have it at work almost every other day and I am very happy with it. I ordered 2 sets of packages for it and a cover on Ozone.

Good afternoon, accept me and I thought for a long time, made up my mind, chose but stopped at REDMOND RVS-M020, I wanted Redmond RVS-M021 to be attracted by the presence of containers, but in Ukraine they simply DO NOT, but I ordered RVS-M020 on Rozetka, but the question is which ones to take in Ukraine There is no set of containers for a vacuum sealer. I repeat I am from Ukraine. Tell me who is from Ukraine

I have a CASO VC 150. Everything was fine, but not for long. With the modes, everything is fine, maybe by myself, you can forcibly turn on the sealing, there is a mode for wet products. He just began to make holes at the seams in places, solder through. Now it is under repair, it was not possible to fix it right away, it will be necessary to install a new sealing strip, it is not available now, whether it will be or not is not known. I'm waiting. At the same time, I began to read the topic again, slowly picking up a replacement.
The workshop is the only one in the whole city, which at least agreed to try to fix it. Others were immediately refused - there are no spare parts, the company does not supply. T. about. we have a disposable device for a lot of money.

Galina, if the packer is under warranty, then you can change or repair.Spare parts are available and are sent to service upon request.
There are two services in Moscow. If there are complaints about the service, then write the address and number of the act / invoice for which you handed over. Thank you.

Ladies, what about the Caso VC 11? In mvideo, bonuses are on, you don't want to dear. Is it worth looking at him at all?

Natasha, the model is similar to CASO VC10 only with a mode for wet products. In MVideo and the price was very good (I don't know how it is now). There are a lot of reviews on CASO VC 10. Read it.

[S-t]

S-t, Valera, Thank you. I read it, yeah. What about the Caso Touchvac Vacuum Sealer? I read it, of course, but for now I'm still choosing between both.

Natasha, Caso TouchVac ...
- outwardly more interesting (in my opinion)
- there is a mode for soft foods
- touch buttons

[S-t]

S-t, Valera, so I'm leaning towards him. Thank you

[S-t]

S-t, can you tell me - where in St. Petersburg do the packers repair? I'm not even lucky with them.
The first was Caso 10 - it passed under warranty. I changed it to Ellrona - it lasted longer, the warranty is over. But there is only one problem: it stops sealing automatically after pumping out, you have to manually press the seal, and so the air partially returns.

Anna, service in St. Petersburg, Obukhovskoy Oborony Ave., 209, tel. (812) 600-11-97

And if you press "stop" and / or "seal" a little earlier than he himself stops pumping, then the air also returns? I tried it on an office copy - it holds.

service in St. Petersburg, Obukhovskoy oborony ave., 209, t. (812) 600-11-97

I handed it over there. They honestly kept it for exactly 45 days and issued a certificate that it was not repairable. And so, I have a CASO 350 and also stopped soldering after pumping out the air. Works manually. But somehow it is not comme il faut, having the CASO technique, to use truncated modes.

[S-t]

S-tso I do it. But I don't like it). Samopalis it during the warranty period? So nothing shines for me?

Galina, if the packer is under warranty, then you can change or repair. Spare parts are available and are sent to service upon request.
There are two services in Moscow. If there are complaints about the service, then write the address and number of the act / invoice for which you handed over. Thank you.

Unfortunately, the warranty has recently expired. I know about two services. In the first one, they immediately refused to repair it due to the lack of spare parts supplies.
They promised to renovate B. Cheremushkinskaya. First, we tried to tighten and straighten the sealing tape, the one that was on the device, but it did not work. They said they ordered a new one and are now waiting. When it will come and whether it will come at all is not known. Has handed over for repair on March 24, while silence.
It looks like you'll have to look for a replacement.

Unfortunately, the warranty has recently expired. I know about two services. In the first, they immediately refused to repair due to the lack of spare parts supplies.
They promised to renovate B. Cheremushkinskaya. At first they tried to tighten and straighten the sealing tape, the one that was on the device, but it did not work. They said they ordered a new one and are now waiting. When it will come and whether it will come at all is not known. Has handed over for repair on March 24, while silence.
It looks like you'll have to find a replacement.

Galina, send me the invoice / act number or name of the person who handed over the device to the service. I can find out what the delay is about. If there is a request from the service, then usually spare parts are sent immediately, but often the services forget or accumulate applications ...

Photographed the box with the sealing elements.

And if you press "stop" and / or "seal" a little earlier than he himself stops pumping, then the air also returns? I tried it on an office copy - it holds.

And how can he hold if the package is corrugated by default inside and it will not be possible to clamp it tightly at all times? This entire path must be sealed, or what? So that after stopping the pump from the outside, air does not penetrate through it. Redmond can't hold that way either.

At first they tried to tighten and straighten the sealing tape, the one that was on the device, but it did not work.

That's it, I also have suspicions in this direction.) That the weakest point is the sealing sticker. She begins to let air pass along the package outside and at least crack the motor, but do not pump the whole room in a circle.) At least mine is very rare, but it starts to show off and buzz until you turn it off, but you should turn it on without the package, as everything is right there, after the first zipper goes into sealing mode.

[S-t]

Samopal, is it during the warranty period?

I had a guarantee. Got money in the store and the next device, CASO 350, helped me buy S-t... Thank you very much Valery !!! ... But after a while, after the guarantee, he stopped soldering on the machine. I took it apart, but I didn't see anything criminal, everything is clean. On the Internet, we managed to find out that something happened to the vacuum sensor and it does not send a signal for sealing. But I'm not an engineer, alas.

Oleg, and in the kit for 350 there is a second copy of the seal. Have you tried changing it?