Electric steam sterilizer "2 in 1" Kitfort KT-2308
The sterilizer allows you to sterilize baby food bottles and other matching accessories. Bottles are placed with their necks down on the seats in the bowl, and the nipples and other accessories are laid out on the underneath, installed on top. You can sterilize 8 bottles at a time.
The control panel has touch-sensitive buttons and status indicators. Three operating modes: steam sterilization; sterilization with drying - at the end of sterilization, the device dries with hot air; drying only. The drying time can be changed from 10 to 60 minutes. At the end of the work, the sterilizer quietly beeps and turns off.
Specifications Kitfort KT-2308
1. Voltage: 220-240 V, 50/60 Hz
2. Sterilization power: 700 W
3. Drying power: 310 W
4. Class of protection against electric shock: I
5. Device size: 292 x 292 x 435 mm
6. Packing size: 307 x 277 x 373 mm
7. Net weight: 2.3KG
8.Gross weight: 2.8kg
Service life: 2 years
Warranty period: 1 year
The product is certified.
Equipment1. Main unit - 1 pc.
2. Bowl - 1 pc.
3. Nipple tray - 1 pc.
4. Cover - 1 settlement.
5. Operation manual - 1 pc.
6. Warranty card - 1 pc.
7. Collectible magnet - 1 pc. * Optional.
Kitfort KT-2308 device
Description Kitfort KT-2308
Preparation for work and useBefore using for the first time, wash all parts of the sterilizer except the main unit in soap and water. Carry out one sterilization cycle with an empty instrument.
Make sure the air filter is installed before using the instrument. Without a filter, a lot of dust will enter the interior of the device. Clean the filter regularly.
Sterilization1. Place the sterilizer on a table near a power outlet and as far away from the edge of the table as possible so that children cannot reach it. For the same purpose, do not allow the power cord to hang from the table.
2. Using a measuring cup, measure out 180 ml of clean water and pour it onto the heating plate. Water should not reach the air duct openings.
3. Place the bowl on the main unit. Place the washed bottles with the neck down on the ledges in the bowl.
4. Place the nipple tray on the bowl and lay out the nipples, covers and accessories on it. Close the bowl with a lid.
5. Connect the sterilizer to the power supply. Press the on / off button. The power indicator will light up.
6. Click on the "Sterilization" button. The sterilization indicator and the operation indicator light up. The display will show "12" —the sterilization time countdown timer in minutes. The water will start heating, then it will boil.
7. When the timer expires, sterilization is over, the device beeps 3 times, the display will show "00". After 5 minutes of inactivity, the device will automatically turn off.
8. Disconnect the sterilizer from the power supply and let it cool down. Then take out the bottles.
Sterilization with drying1. Place the sterilizer on a table near a power outlet and as far away from the edge of the table as possible so that children cannot reach it. For the same purpose, do not allow the power cord to hang from the table.
2. Using a measuring cup, measure out 180 ml of clean water and pour it onto the heating plate. Water should not reach the air duct openings.
3. Place the bowl on the main unit. Place the washed bottles with the neck down on the ledges in the bowl.
4. Place the nipple tray on the bowl and lay out the nipples, covers and accessories on it. Close the bowl with a lid.
5. Connect the sterilizer to the power supply. Press the on / off button. The power indicator will light up.
6. Press the "Sterilize with drying" button. The sterilization, drying and operation indicators light up. The display will show "12" - a countdown timer for the sterilization time in minutes.
7. Press the Timer button to change the drying time. The display will show and will flash "30" - the countdown timer of the drying time in minutes.
To set the timer, successively press the Timer button. The drying time changes cyclically in the range of 10-60 minutes in 10 minute steps, the selected time is shown on the display. By default, the timer is set to 30 minutes. Wait a few seconds for the settings to apply. The display stops flashing, then the sterilization timer is displayed again.
8. The water will start heating, then it will boil. During sterilization, the sterilization indicator lights up continuously and the drying indicator flashes.
9. Sterilization will end either when the timer expires or if all the water has boiled off before. The appliance switches to drying. The sterilization indicator will go out and the drying indicator will light up continuously. The display will show a countdown timer for the drying time. The fan will turn on, which will blow hot air through the sterilizer bowl.
10. When the timer expires, drying is over, the device beeps 3 times, the display will show "00". After 5 minutes of inactivity, the device will automatically turn off.
11. Disconnect the sterilizer from the power supply and let it cool down. Then take out the bottles.
DryingIf you have just completed a sterilization cycle and have not removed the bottles yet, start from step 5.
If you need to dry your washed bottles and accessories, start from step 1.
Please note that drying is not a substitute for sterilization!
1. Place the sterilizer on a table near a power outlet and as far away from the edge of the table as possible so that children cannot reach it. For the same purpose, do not allow the power cord to hang from the table.
2. No need to fill in water.
3. Place the bowl on the main unit. Place the washed bottles with the neck down on the ledges in the bowl.
4. Place the nipple tray on the bowl and lay out the nipples, covers and accessories on it. Close the bowl with a lid.
5. Connect the sterilizer to the power supply. Press the on / off button. The power indicator will light up.
6. Press the "Drying" button. The drying and operation indicators light up. The display will show "30" - a countdown timer for the drying time in minutes.
7. To change the drying timer, press the Timer button in succession. The drying time changes cyclically in the range of 10-60 minutes in 10 minute steps, the selected time is shown on the display. By default, the timer is set to 30 minutes. Wait a few seconds, the numbers on the display will stop flashing, the settings will be fixed.
8. When the timer expires, drying is over, the device beeps 3 times, the display will show "00". After 5 minutes of inactivity, the device will automatically turn off.
9. Disconnect the sterilizer from the power supply and let it cool down. Then take out the bottles.
Tips & TricksAttention! During sterilization, do not open the lid, and do not place your hands over the lid to avoid scalding by the hot steam. After the end of sterilization, wait at least 2 minutes for the steam to escape before opening the lid. Be careful not to burn yourself!
Measure the exact amount of water in the bowl. Less water will shorten the sterilization time and the bottles may not sterilize properly. Excessive amounts of water can damage the device.
If at the end of sterilization the sterilizer lid is not opened, the bottles will remain sterile for 3 hours.
Press the on / off button to manually turn the sterilizer off. The drying timer can be changed at any time during the sterilization and drying process. During operation of one mode, you can switch to another mode.
Cleaning, care and storage
Disconnect the sterilizer from the power supply and allow it to cool completely before leaving or servicing. Wipe the cabinet with a dry or damp cloth. After each use, blot any remaining water from the heater, then wipe the heater with a damp cloth. Clean all parts of the sterilizer except the main unit with soap and water. Do not use abrasive, aggressive or antibacterial cleaners and chemicals for cleaning. Do not use a dishwasher for washing. Do not immerse the main unit in water or wash it under the tap.
Remove the air filter regularly and dust it off. Pull the filter forward to remove it. Clean the filter, rinse with water if necessary. Then put the filter back in.
To remove scale from the heater, pour 50 ml of vinegar and 100 ml of water on it, wait 30 minutes, then drain the solution. Wipe down the heater several times with a damp cloth. Then pour 100 ml of water onto the heater, wait 5 minutes and drain. When draining water, be careful: water must not get inside through the air outlet holes on the side of the heater; drain the water away from these holes. It is recommended to descale at least once a month.
Store the sterilizer in a cool, dry place out of the reach of children.
Please read the instruction manual carefully. Pay special attention to safety precautions. Always keep the instructions handy.
1. The device is intended for domestic use and can be used in apartments, country houses, hotel rooms, offices and other similar places for non-industrial and non-commercial use.
2. Use the device only for its intended purpose and in accordance with the directions set forth in this manual. Misuse of the device will be considered a violation of the terms of proper use.
3. Before connecting the device to an electrical outlet, make sure that the power ratings indicated on the device match those of the power source being used.
4. To prevent electric shock, do not immerse the device in water or other liquids.
5. Do not carry the appliance by the power cord. Do not pull on the power cord when disconnecting the plug from the outlet.
6. Do not use the device if the power cord, plug, or other parts of the device are damaged. To avoid electric shock, do not disassemble the device yourself - contact a qualified technician to repair it. Remember, improper assembly of the device increases the risk of electric shock during operation.
7. Children, people with reduced physical, sensory or mental capabilities, as well as people who do not have sufficient knowledge and experience, are allowed to use the device only under the supervision of persons responsible for their safety, or after instruction in the operation of the device. Do not let children play with the appliance.
8. Supervise the operation of the device when children or pets are nearby.
9. Do not turn on the device without water. This could damage the device.
10. Do not leave the working device unattended. Turn it off and unplug it when not using the device for a long time or before performing maintenance.
11. The body of the device can become very hot during operation. Do not touch hot surfaces with your hands. Be careful! Risk of burns possible!
12. Place the device only on a stable horizontal surface at least 10 cm from the wall and edge of the table. Install the appliance so that children cannot accidentally touch the hot surfaces of the appliance.
13. Do not try to bypass the power-on lock.
14. Do not drop the device or subject it to shock.
15. Keep the device out of the reach of children.
16. Use only accessories or components offered by the manufacturer.Use of other optional accessories may damage the device or cause injury.
