Electric potato peeler

As I understood. difference in the lid. The one that is white does not close.

Probably, I also overdid the water, although I poured it before the mark. But I covered it with a towel and everything is fine.

Likewise, there were also dances with a towel. Water should be poured even less.

I got mine too. Is the water level mark F 1 L? We put potatoes in one row? The lid is flimsy, the "ears" - the latches are scary to snap, so as not to break.

yes, just messed up, it's a mark. Potatoes in one row. The lid is not very flimsy, the latches are simply removed. Yesterday I cleaned potatoes in it again, for shingles. Don't be afraid to use it! You just feel your disappointment. She is not as scary as she seems.) Very comfortable, she is not afraid of anything. On the first day, I poured it, when I picked up the water, how much to pour. She wiped it off and continued to use it further. Somehow I'm not even afraid, although they write - not more than two minutes to use, I just skillfully clean up in several approaches, as many potatoes as I need.

I also want such a thing. Of course, I don’t have to peel 10 kg of potatoes, but I also have a corn on my index finger from my modest cleaning (somehow it comes out to me to hold a knife, which happened like a corn). Is it laborious to wash it? I have never seen them live, are there graters like those of a juicer or some other principle? Thank you

oh, washing is not difficult. I cleaned it, rinsed it like a bowl, wiped it off, and put it on the axle. I poured some water, filled up a potato, covered it with a lid and a cloth, turned it on and cleaned it. And that's all. And before I think that I need to peel potatoes, it takes such a bummer .... The hand in the wrist hurt forever and got tired of calluses. I'd rather use the technique than cure calluses.

Now I want her even more, otherwise the corn on the bend of the index finger already hurts

I got the second one today, I have some kind of fear, what if I clean it again with my hands? My husband said take it. Without hesitation. I put it in the pantry, it will be high.) I also have a corn on my index finger. I ordered it in the same store that I gave the link to. They said they had five more pieces left. Just after having "tasted" such an assistant as a potato peeler, you will not stop. And if one breaks, immediately look for a replacement.

You all write so well about the potato peeler that I also looked after Maestro MR 770 for myself. I will make myself a present for St. Nicholas.
I will take here 🔗... Already phoned, usually always available. I hope that it will be on my share.

and I have trouble - my maestro 771 stopped working somehow so suddenly, I didn't understand why, the grater just stopped spinning, but tried to start-spinning without potatoes

and I have trouble - my maestro 771 stopped working somehow so suddenly, I didn't understand why, the grater just stopped spinning, but tried to start-spinning without potatoes

I feel sorry for the same sorrow, but our trouble can be helped. The pin on which the grater is put on is put on the motor pin from the back (bottom) side (just like the handles on the gas stove) and has the shape of a crescent. If you put large potatoes, or a lot, or angular pieces, then the motor pin grinds off this crescent-shaped limiter making it round, and the grater loaded on the axis is scrolled.
Medicine - Epoxy does not help, you can not try (like any other glue), I also want to insert a small plate across if it holds a load of potatoes, then OK, and if it doesn’t help, then you need to call the service centers and look for a spare. part entirely.
The moral is to follow the instructions strictly and not to overload. (this is for me personally)
I'll try to insert a photo.

[Critical errorThe script was called without the required parameters.]

Not inserted, writes:
Critical error
The script was called without the required parameters.

I try with single files.

[YanOchka-]

YanOchka- if it helps, be sure to write, I already felt a little better, otherwise there is now neither time nor funds to contact service centers.
In general, it's a shame, of course, all year I peeled only small, round potatoes, and strictly no more than 1 kg, and as soon as the warranty year ended, I got bummed: together with the small ones I threw a couple of medium-large potatoes, they began to get stuck and I took them out, cleaned them the rest are normal, then I cleaned it again normally, and then after a couple of days I turn it on, but it no longer turns

and I have trouble - my maestro 771 stopped working somehow so suddenly, I didn't understand why, the grater just stopped spinning, and tried to start-spinning without potatoes

I have the same trouble .... without potatoes, twists, but with her, in any way. Now I use the second one. I'm even afraid to tell my husband, 600 UAH. spent two. And everything is down the drain (

IT TURNED to insert !!!
Here he is this pinBut IT, the hole, has become almost round.
By the way, the instructions say that after work, the rest should be 10 minutes. to cool the engine. Maybe because the engine pin is hot, it melts, and then turns this pin of ours?

Interestingly, and the potato peeler Tosh for 5000 also breaks in this way?

that's probably my trouble too ..... And what to do now? I can't get such a thing out of a potato peeler ... How did you manage to see this pin?

Do we have anyone Tosh? I've been thinking about her for a long time, only I haven't found any feedback.

In fact, getting to it is very easy.

1. It is necessary to turn the main bowl upside down, and unscrew the 4 screws. The bowl can be easily divided into 2 parts: the main part and the flat bottom.

2. We remove the bottom, and in the main bowl we look where the occasion fits.
It is attached to a small metal motor box, on which our pin sits.

3. To remove it, unscrew 4 more screws and carefully pull the box out of the groove towards ourselves so as not to rip off the rest of the wiring going to the light bulb, switch, etc.

4. It's all easy, you don't just have to rush and tug.

5. The box is pulled out together with the pin, which we gently pull up and remove.

If something is not clear, I will then drop the photo.


Oh, the photo is mixed up, we look in the reverse order - from right to left.

AND SEPARATE THANKS TO THE MODERATOR-ADMINISTRATOR for simplifying the insertion of photos into the text. It became VERY comfortable.

[YanOchka!]

YanOchka! Thanks for the photo story! My potato peeler Saturn, alas, died quickly. There were no spare parts in the service. The store returned the money. The problem is the same with the pin. Are there any considerations --- if we immediately strengthen this problematic part of the new potato peeler? And you can find out everything about Toshi from the manufacturer. I wrote to the email address --- responded quickly. But with delivery to Ukraine, Tosha will be gold.

YanOchka- you are super! Thank you! I'm exactly the same. I sit and think, and how to strengthen this pin .... So far nothing sensible has occurred to me. Why didn't I try today ... I even had such a thought, a piece of light tin ... then I changed my mind. Here are the manufacturers of g ... and then we sit and think about how to fix it ...

Girls, or maybe try to make a liner of hard rubber (like on car wheels or boot rubber, from which heels are made). I don't know how long such an insert will last, but you don't mind them - you can always make new ones.

Here are the manufacturers of g ... and then we sit and think about how to fix it ...

Yes, not thought out, on the other hand. if there is a metal groove, then when the potatoes get stuck, the pin will no longer start to scroll, but the motor may jam. And to fix it ...

... or maybe try making a hard rubber liner

The motor pin should, having hooked the pin, scroll the loaded grater.And even at speed. So the pin needs a stop and is hard enough. A stop that will be rigidly fixed, and which will not be able to twist itself inside the grinded hole.
Based on this, I think that the rubber seal will either twist or burn from the friction of the parts. Here is a metal bar to insert, or rather implant it into the inner opposite walls, like a spacer. In this case, if something gets stuck in the grater, then the pin itself will disintegrate into halves and you will definitely have to contact the service to send the app. parts. Or, as an option, go to the turner while the pin is intact and grind it out of metal. But here, in case of overload, the motor will already start to burn .... Hmm-ah.
Probably have to involve men here, whether you want it or not.

Girls, there is news regarding the breakdown. I contacted the office. website with the manufacturer. This s / h is sent to the address (probably by mail). You just need to send a scan of the warranty card to them by mail. I ordered several at once.
They said that they can send them through the online store where they bought.
I called the specified numbers of service centers - they do not answer. I called the contact tel. and sent a duplicate request by email. manufacturer's box with office. site.
BUT I have Aresa and a manufacturer in Belarus. My call was answered immediately.
What are your models?

[YanOchka-]

YanOchka-
I have maestro 771
What city do you live in?

I ordered on ozone Smile, now I'm waiting. I wonder if he will come with a greenery dryer or not? In the comments under the product, no one writes about this, it is absent in the description.
But on the forum, the girls wrote that there was a centrifuge. I dream ...

I ordered on ozone Smile, now I'm waiting. I wonder if he will come with a greenery dryer or not? In the comments under the product, no one writes about this, it is absent in the description.
But on the forum, the girls wrote that there was a centrifuge. I dream ...

Dreaming is good, only you have enough small potatoes? The large one is not so well cleaned there.

on the forum the girls wrote that there is a centrifuge. I dream ...

There is.

The large one is not so well cleaned there.

Yeah, and at the same time, the device itself breaks

Yeah, and at the same time, the device itself breaks

And what breaks first? I read a bread machine on the forum. no - the bushing breaks, but they are about the Hiltons. Does this detail fly in Smile too?

There is.

Oh, I want, I want! And then I wanted a drier-taper, but the price bites. And it flows down in a colander for a long time.

Dreaming is good, only you have enough small potatoes? The large one is not so well cleaned there.

Sorry. Well, I will choose flat and small in the store.
So it will look even more aesthetically pleasing on a plate.

And what breaks first? I read a bread machine on the forum. no - the bushing breaks, but they are about the Hiltons. Does this detail fly in Smile too?

I won't say for Smile, I didn't use it, but they all have the same sore. The inner hole of the pin is grinded, on which the grater itself is put on, when overloaded and when large potatoes get stuck. She cannot turn it. Just be careful.

I won't say for Smile, I didn't use it, but they all have the same sore. The inner hole of the pin is grinded, on which the grater itself is put on, when overloaded and when large potatoes get stuck. She cannot turn it. Just be careful.

Thanks, I'll keep it in mind. I won't be large at all (yes, I usually bake it in a peel).
Although, nothing lasts forever under the moon. But I have a familiar lathe operator. Maybe just make the piece forever?

... But I have a familiar lathe operator. Maybe just make the piece forever?

It would be great. And at the same time find out how much such a service can cost? Only mindfulness does not hurt anyway. Because in this case, the motor is weak, the inner hole will not be able to crank, which means it will jam and may burn out. And the motor is even more expensive to look for and install. I think so. Although...I say, men should be connected.

It would be great. And at the same time find out how much such a service can cost? Only mindfulness does not hurt anyway. Because in this case, the motor is weak, the inner hole will not be able to crank, which means it will jam and may burn out. And the motor is even more expensive to look for and install. I think so. Although ... I say the same, men should be connected.

My ice cream sleeve cost a can of coffee.))) I think it will take about the same amount.
If this is a simple pin, then a little.

And how much does the part cost in the service?

Your manufacturer LLC "Phill-Maestro" ()

Thank you very much for the info there is no sleeve available, but they said at the end of the week they would answer if they could find it somewhere

What I found. On the official website of Vitesse there is such a potato peeler, very similar to the Belarusian one (the cap looks like the same orange one). Inside was dried-centrifuge.
🔗
I hope the link opened normally, if not - the main site has this device among the new products. Unfortunately, prices are not listed there.

I secretly hope that it will be offered for "chips" in Dixie! I want either to stock, or for gifts although I have never used it myself
I'm waiting for my Smile, I dream of Vitesse.

: girl_cray: h-yes ..... my joy was not long, and now what to do with this Maestro MR 771 potato peeler? I have two of them. It was ..... well, of these manufacturers with such bushings. I tried all the firms. Now the maestro is on the dump ..... even though it is now clear what was breaking in them, what will we try next? The most offensive thing is that I tried to protect them. I didn't overload it, everything was as per the instructions ...

And how much does the part cost in the service?

I could not get through to them. I'll let you know later.

... what are we going to try next?

I like. Not discouraged spirit !!!!
We must start with Toshi, I have been looking at her for a long time, but the place needs to be stationary, and how to find out what is inside her. The same "snot"?

.... there is a familiar lathe operator. Maybe just make the piece forever?

Or so.

: girl_cray: h-yes ..... my joy was not long, and now what to do with this Maestro MR 771 potato peeler? I have two of them. It was ..... well, of these manufacturers with such bushings. I tried all the firms. Now the maestro is on the dump ..... even though it is now clear what was breaking in them, what will we try next? The most offensive thing is that I tried to protect them. I didn't overload it, everything was as per the instructions ...

And how long do they serve on average? And how many times a week did you use it?

We must start with Toshi

Does Toshi have a warranty and service? And then the price is somehow ... almost like an economy class dishwasher. Are there any familiar users of this device?

Answer: for the sake of frugality of the gadget, I used it three to four times a week. Every potato peeler, from all firms that produce them in Ukraine. The maestro was something new (I hadn’t heard such a company yet and hoped that at least it would last a long time .....). Not destiny ..... Now these two last potato peelers are in a box. Return - refuse to accept it g ... back, and two weeks have already passed. Do not fix it. Here at least a trash can in the general collection. As a monument to my stupidity, well, they have not yet learned how to make a normal potato peeler, except for industrial ones, for a simple housewife.

[AlenaDS]

AlenaDS wait for the trash can in the general collection. Fill in the name of your cleaner in the search engine and then fill in - of. website. Must give out the manufacturer (at least one of your machines). Then try to call. Well, the manufacturer cannot ignore it, these are stores and service centers are "wise-lazy". Ask to send zap. part. Or maybe there is a service center nearby, so they can send it through it. In general, it is too early to despair. Not all paths have been traveled. as a last resort there is always a turner. My s / part = 120 rubles + shipping. It makes sense! And sign off what happens. It's easier together.
The service life is different for everyone. Someone uses it for 1.5-2 years. And someone .....I lasted 2 weeks, several times a day, that is, regularly. And then we bought, well, O-O-VERY large potatoes, cut them into 2-3 pieces, and for some reason there was a misfire ... The grater stuck, and again, again. Now I'm waiting for the app. part.

Answer: for the sake of frugality of the gadget, I used it three to four times a week. Every potato peeler, from all firms that produce them in Ukraine. The maestro was something new (I hadn’t heard such a company yet and hoped that at least it would last a long time .....). Not destiny ..... Now these two last potato peelers are in a box. Return - refuse to accept it g ... back, and two weeks have already passed. Do not fix it. Here at least a trash can in the general collection. As a monument to my stupidity, well, they have not yet learned how to make a normal potato peeler, except for industrial ones, for a simple housewife.

Clear. One thing is not clear.
If the device really serves for 2 weeks, why is everyone so happy here?
Maybe cars of a certain brand break down more often?
GIRLS !!!
1. Who and in what time frame did the potato peeler break down?
2. What brand was it?
3. How often have you used it?
4. Were you able to order a spare part?

[AlenaDS]

AlenaDS try to call. Well, the manufacturer cannot ignore it, these are stores and service centers are "wise-lazy". Ask to send zap. part. Or maybe there is a service center nearby, so they can send it through it. In general, it is too early to despair. Not all paths have been traveled. as a last resort there is always a turner. My s / part = 120 rubles + shipping. It makes sense! And sign off what happens.

Is it possible to order in advance or give only under warranty in case of breakdown?
In my city, judging by the information from the Smile website, there is no authorized service center. How then to be?
If you order from a lathe-machine operator (there is a possibility) - how does this detail look like? Is there a photo anywhere? I'm a noob: oops: User only.
Do you have a smiley by any chance? (very hope so)

The service life is different for everyone. Someone uses it for 1.5-2 years. And someone ..... I lasted 2 weeks, several times a day, that is, regularly. And then we bought, well, O-O-VERY large potatoes, cut them into 2-3 pieces, and for some reason there was a misfire ... The grater stuck, and again, again. Now I'm waiting for the app. part.

Which ones serve for a year or more?

[AlenaDS]

Clear. One thing is not clear.
If the device really serves for 2 weeks, why is everyone so happy here?
Maybe cars of a certain brand break down more often?
GIRLS !!!
1. Who and in what time frame did the potato peeler break down?
2. What brand was it?
3. How often have you used it?
4. Were you able to order a spare part?

haven't worked even a month

SATURN

2-3 times a week

the service center was missing a part. The store returned the money

AlenaDS ! After all, your broken potato peelers are under warranty? If the service refuses to repair due to lack of spare parts. Call the Consumer Protection Society. They will tell you what to do. Do not give up and do not throw anything away!

Is it possible to order in advance or give only under warranty in case of breakdown? In my city, judging by the information from the Smile website, there is no authorized service center. How then to be?

So, in order.
1. First, call the MANUFACTURER and ask, all conditions are different.

If you order from a lathe-machine operator (there is a possibility) - how does this detail look like? Is there a photo anywhere? I'm a noob: oops: User only.

the photo is on the previous pages, look through.

Do you have a smiley by any chance? (I hope so) Which ones serve for a year or more?

No, I have ARESA. She also served 1.5-2 years, but in other hands.
I suppose it's not about the brands, but about the design and material itself. They are plastic (bushings) for ALL models. From here and dance. I also thought to offer the manufacturer to report this pin in the kit, then all the issues will be resolved on their own, after all, put this detail on one or two.But they seem to be wary of the fact that not everyone is strong in technology, so they offer a replacement in the server. center. But where to get them, these services ... And everyone is happy because it is convenient and fast. Having tried it once ..... It's like a washing machine, it doesn't wash all stains, but everyone in the house has it.

Girls, I answer all at once) was: Saturn ST-FP8507, Hilton KS 3219 Silver, ARESA P-01, Maestro MR 771 (2 pcs.) - they are standing now, do not work. HILTON KS 3218, Maestro MR 770, etc. This so far she has listed which she managed to shake off back within 14 days back. Of all of the above, maestro 771 worked most of all, it's a pity that she covered herself after 14 days (I paid 600 UAH for two pieces). With this maestro, a complete kapets. They do not want to repair it under the guarantee, they turned to the consumer union-full ..... ny. Only two months have passed since the date of purchase. Potato peeler, as I understand it, this is not my gadget ..... So I have already given up all hopes for such an assistant. Wringing your nerves even after you've laid out your whole soul and tugged at it, is it worth it? I will also try to write an electronic letter to the Maestro's office. Maybe this will help you somehow get your money back for this g .... All potato peelers are good only for young potatoes. And then, not very large.

I've been following this topic for a long time, the epic with devices. I noticed that all the potato peelers that are on sale are only from very budgetary manufacturers with a very unstable reputation.
Therefore, the forecast was clear to me from the very beginning.
I don’t believe Smiles, Saturns and the like.
Interestingly, but Bosch, Phillips, Kenwood, .., produce potato peelers, I have never met either in the internet or in stores.

they produce something, only in food processors for 10 thousand, such as Kenwood 🔗

Yes, I know what is produced in the form of additional attachments-attachments for expensive combines. But there is no independent device - a potato peeler.

[AlenaDS]

Based on the above, I can pay attention to Tosha. The case seems to be metal, probably even stronger inside the part. Price in the region of 5000 rubles. with a penny.
AlenaDS when you write a letter to the maestro's office, ask how they can send (send, transfer) the detail to you. Take several at once if they are the same on all models. By the way, maybe the truth is to disassemble them and check the cross-section diameter of all. As I understand it, it won't get any worse. And the hope for their resurrection ..... still remains.

Is it true, if the design is the same, maybe the spare part will be compatible for different models?
I also wrote in a smile at their office. site about spare parts and am waiting for an answer.
Ozone writes that my order has been sent to the delivery service. I'll get it soon.