KitchenAid Mixer

Eh, and from me 840 km
Please, write if you find where you can buy ... With a quick search for the Internet, only Amazon and ebay gives out ...

Maybe you have a radio market in your city?

Clear. We will not replace it. How do you recognize the signs that you need to lubricate?

Perhaps there was a wrong impression that I am a mechanic, or an employee of a service center, but this is not so) my education is by no means engineering, I just ran into a problem and was puzzled by the question, having furrowed our and foreign forums
To be honest, I don’t think at all that the lubricant there needs to be changed when I saw how much of it there ... 6 ounces is a confident glass of lubricant, sit on the jelly, in fact, everything is clogged with it, not that a finger was dropped, but just gears in the slide of this grease)
Rather, there are times when the grease has to be removed, since it sometimes leaks during long work and overheating, and this, by the way, is considered the norm and you should not panic

[e1win]

e1win, maybe there is. But if I understand correctly, is this a detail from the mixer? Doesn't fit with anything else? If so, then it is unlikely that such a detail is on the radio market in our small town ...

[caprice23]

caprice23, it is most likely best to order at your nearest Kitchen service workshop. They will order and if they themselves cannot install, then they will install. So I ordered a new touch control panel for the Bread Maker. First, find on the Internet by request in a search engine where it is nearby and first talk on the phone, and then drive up and order.

As I wrote, this is the simplest option, it is also costly, because if caprice23 is a spouse, or a father can hold a soldering iron, then repairs will cost less than 100 rubles (about 50 rubles for a triac and 5p diac)
The word soldering is also rather scary and loud, in fact, you need to make 4 points there

e1win, maybe there is. But if I understand correctly, is this a detail from the mixer? Doesn't fit with anything else? If so, then it is unlikely that such a detail is on the radio market in our small town ...

I did not understand you, you just asked me in HP about the triac and diac, I thought you were looking for them to replace them on the board
If you are looking for a complete part, then on the Internet I saw even in the Russian Federation several offers of about 2-2.5 tr
If you order something from abroad, I will throw a link to authorized whirlpool dealers (they are the ones who make spare parts for the kittens), you can buy any parts from them, if you wish, you can remake the Artisan for 220 volts by purchasing the necessary parts

spouse, or father can hold a soldering iron

May
Now I have a question where to get the details? Only American sites are given out ....

I did not understand you

I asked you about the whole board and about the separate diac and triac. To work through all the options and decide how best))) Suddenly it will not be possible to find one or the other)

on the Internet I saw even in the Russian Federation several sentences of about 2-2.5 tr

If it's not difficult, can I have a link?

I'll throw a link to authorized whirlpool dealers (they are the ones who make spare parts for the kittens), you can buy any parts from them, if you wish, you can remake the Artisan for 220 volts by purchasing the necessary parts

And this is very interesting.

[e1win]

e1win, maybe there is. But if I understand correctly, is this a detail from the mixer? Doesn't fit with anything else? If so, then it is unlikely that such a detail is on the radio market in our small town ...

and the most important!!!!
If you buy a whole board, and do not change the elements on the old one, do not confuse the voltages, those, if your kitchenaid is 220 volts, you also need this bar 220 volts, if you bought a mixer in the us, then you should not buy a bar in Russia, because they are 220v
If you bought in the usa, you need to look for 110 in the Russian Federation (which is unlikely), or order from the usa
(Or change all elements on the board

May
Now I have a question where to get the details? Only American sites are given out ....


I asked you about the whole board and about the diac and triac separately. To work through all the options and decide how best))) Suddenly it will not be possible to find one or the other)


If it's not difficult, can I have a link?



And this is very interesting.

Now I will try to raise it, I definitely saw it somewhere

According to the bar that I threw - the part number for Americans, for 120v mixers, for users of 220v models bought in Russia or Europe, the part number W10538289

I can't throw links yet, they write that it is still green

[and the most important!!!!]

and the most important!!!!
If you buy a whole board, and do not change the elements on the old one, do not confuse the voltages, those, if your kitchenaid is 220 volts, you also need this bar 220 volts, if you bought a mixer in the us, then you should not buy a bar in Russia, because they are 220v
If you bought in the usa, you need to look for 110 in the Russian Federation (which is unlikely), or order from the usa
(Or change all elements on the board



Now I will try to raise it, I definitely saw it somewhere

According to the bar that I threw - the part number for Americans, for 120v mixers, for users of 220v models bought in Russia or Europe, the part number W10538289

I can't throw links yet, they write that it is still green

e1win, excuse me, I've already tortured you all, but you have to figure it out completely.
My mixer is American, that is, 110.
If you do not change the entire board, but only the elements on it, do they also depend on the voltage? They, too, cannot be found here and must be ordered?

Links, if you can in a personal

[caprice23]

caprice23, there is a chip dip store, look there for details to generally understand what kind of nonsense we are talking about
Type in there in the search
DB3TG, Dinistor 30-34V 2A
Triac bta06-600sw

e1win, excuse me, I've already tortured you all, but you have to figure it out completely.
My mixer is American, that is, 110.
If you do not change the entire board, but only the elements on it, do they also depend on the voltage? They, too, cannot be found here and must be ordered?

Links, if you can in a personal

No, with these details everything is ok, they are, let's say, universal, the part numbers are the same as in the English-language forums, which we have
P. s. Here are the best quality mixers for the domestic market

[e1win]

Here are the best quality mixers for the domestic market

I also thought about it



e1win, please write how you can solve your problem. What did we manage to do.

Type in there in the search
DB3TG, Dinistor 30-34V 2A
Triac bta06-600sw

I looked. The price is a fairy tale)). And what is a deacon? You also need him? Or is this a dinister? (God, what kind of teapot I am in these matters)
Also, sorry for my importunity ...

And above you wrote STA06-600SW, not Triac bta06-600sw ... What is it all the same?

[e1win]

I also thought about it



e1win, please write how you can solve your problem. What did we manage to do.


I looked. The price is a fairy tale)). And what is a deacon? You also need him? Or is this a dinister? (God, what kind of teapot I am in these matters)
Also, sorry for my importunity ...

And above you wrote STA06-600SW, not Triac bta06-600sw ... What is it all the same?

Db3 is a diac, and sta06 is a triac, they are also a dinistor and a triac

STA06-600SW

Bta, apparently an American member of the forum described himself, and I repeated after him, triac bta06-600sw

[e1win]

e1win, everyone, I understand, thanks

I turned the screws. The speed does not change. Pancake
At 6, as it should be, 1,2,4 spar like mad.

[e1win]

e1winAnd you can remove the video for Natasha caprice23 and others and the instructions for repairing the speed adjustment will be more clearly more accurate, you can always peep, and if there is an error, then fix it. If there is no service center nearby, then you really have to order parts through the online store, and the hands can be corrected according to the video instructions. And most importantly, this instruction can be used on our Bread Maker. RU. Who has the same problem and nowhere to repair. On the video, you can take pictures of how to detect the wrong operation, how and where to open, unscrew and what to unscrew, what to change and how to change and tighten and reassemble everything and check the good corrected work. I am grateful in advance and I will be happy for those who will be helped by this (I have no problems with the mixer and regulation, and there are enough services in Moscow). This is for those who have a problem and nowhere to fix it.

This is for those who have a problem and nowhere to fix it.

I will support

I will support

I threw off caprice23 quite visual video, as far as I remember
Ask her to post here, there is a video from the service center (in English), completely showing the stages of replacing the control board and setting the speed

I threw off caprice23, a very descriptive video,

I got confused with these screws. They were initially very much twisted from me. At first I tried to regulate them from the starting position. Then I saw that in the video the screws were screwed to the end and he then adjusts them. I tried this. Not a fig. I don't know what I ended up doing there now. : -



Translate, please, who understands how many mm the screws should be tightened? And from where to where to measure?

I don't know what I ended up doing there now.

that's what I'm afraid of.

[If you need to get the speed faster, then turn the screws counterclockwise (direct translation "unscrew"). If the mixer does not carry out circular movements at all, then the screws are tightened too much, it is necessary to unscrew.]

4:20 - he measures the distance between the board and the base of the screws with a ruler (see the ruler), which was originally in the mixer. It should be 3/7 inches (the video is American, as far as I understand, so convert American inches to centimeters)

After installing the new board, he explains that the top two screws are responsible for regulating the speed at low speeds.
11:40 - If you need to get the speed faster, then turn the screws counterclockwise (direct translation "unscrew"). If the mixer does not carry out circular movements at all, then the screws are tightened too much, it is necessary to unscrew.
12:00 - it adjusts 1 turn faster.
Next, we adjust the number of revolutions at 6 speeds. It should correspond to 180 rpm. You need to turn on the timer and count 45 knocks on the finger in 15 seconds.
13:25 - screw in (clockwise) - to increase, unscrew (counterclockwise) screw - to decrease the rotation speed



OlgaGera, Lelka, you also have problems at low speeds, or what?

Do you have problems at low speeds too, or what?

well yes. So I think, should I turn the screws? Or .. not to interfere with the machine to work?

Or .. not to interfere with the machine to work?

If everything is delicious with you and it never bothered you - don't bother. I changed my hand mixer because I was pissed off by the "fast" first speed ...

Another question is that you now know this and whether you can use the device with this thought. If you can, then leave it alone, of course.

Do you have an American?




Fir-trees, I would have opened, probably. Curiosity would win! The guy works so nicely with kitschen in this video. The beauty is simple!

Only you noticed that there you still need to apply grease to the new board and screw in a small screw NOT all the way - to make room for thermal expansion.

Do you have an American?

no, local))))
Let it work)))

[Svetlenki]

Svetlenki, Svetul, thank you very much. And then I'm not boom boom.

It should be 3 and 7 inches

Inchi is inches. Hmm, a strange figure in cm turns out. Very big. Something wrong . ..

He changes this board to a new one. It does not regulate ..

Doesn't regulate? At the end, he pokes the screws with a screwdriver so demonstratively, turns on the speed and checks the revs, that I thought he was explaining how to adjust the speeds. Eh ...

If everything is delicious and it never bothered you - don't bother

And that's exactly what annoys me. You read the recipe "stir at first speed", what kind of stir there, there is a devil! But I unknowingly decided that it should be so. And she resigned herself.

Inchi is inches. Hmm, a strange figure in cm turns out. Very big. Something wrong . ..

Natasha, she called her husband. You must be so disgraced! In general, 3/7 inches. Translated into cm, having previously done mathematical operations (one divided by seven and multiplied by three is 0.43) - it turned out 1.0922 cm. Looks like? Translated by this link

🔗

And this is a 4:20 video of him showing a ruler. Turned centimeters would still show a radish!



So. I didn’t even watch the end of the video, but there is all the most basic. I'll take a look, take notes and come back

You must be so disgraced!

Light, what are you talking about! I'm the disgrace here, no boom boom in English

it turned out 1.0922 cm. Looks like?

Yeah thanks!

Turned centimeters would still show a radish!

Don't say



Light, but does he say anything about the lower screw? They don't even seem to show how it is screwed. It's just that I had it twisted quite strongly, but in the video it seemed to be twisted to the end ...

Light, but does he say anything about the lower screw? They don't even seem to show how it is screwed. It's just that I had it twisted quite strongly, but in the video it seemed to be twisted to the end ...

We'll fix your mixer right now. You have all the problems due to the fact that it is very twisted. For the convenience of future generations, I will now supplement my first post on video with a translation. Good?

Right now we will fix your mixer

I will now supplement my first post on video with a translation. Good?

[e1win]

e1winplease see my post above KitchenAid Mixer # 1866

especially what is in bold. Did I understand the video correctly?



caprice23, Natasha, I'll eat you now! Do you know that in this video you can turn on Russian subtitles ???

[Svetlenki]

Natasha, I'll eat you now! Do you know that in this video you can turn on Russian subtitles ???

I'm calling from phone. They don't turn on here, I tried



Svetlenki, Svetul, please forgive me for puzzling you. But if I could turn on subtitles, then of course I would not torture you

Only you noticed that there you still need to apply grease to the new board and screw in a small screw NOT all the way - to make room for thermal expansion.

This is not a lubricant, but thermal paste, as I understand it, is applied like a triac "radio box" to dissipate heat to the mixer body

This is not grease, but thermal paste, but I understand only

You are absolutely right! These are the features of my translation

Please tell me, did I understand correctly that the upper and lower screws must be turned in different directions to achieve the same result? That is, to accelerate the lower speeds, the upper screws must be unscrewed (counterclockwise), but at 6 speeds, the lower screw must, on the contrary, be screwed in. Did I understand correctly and precisely?

Svetul, please forgive me for confusing you. But if I could turn on subtitles, then of course I would not torture you

Yes, I understand. But I don't mind helping you. Moreover, the video is so sensible, and our Kitchen is so beautiful inside - it's just lovely!

[e1win]

e1winplease see my post above KitchenAid Mixer # 1866


especially what is in bold. Did I understand the video correctly?



caprice23, Natasha, I'll eat you now! Do you know that in this video you can turn on Russian subtitles ???

I described these manipulations
Use the upper ones to adjust the washing (the first speed is 60 revolutions), spin it - it lowers the speed, unscrew it - it increases
To tune the sixth (after pastroor the first), twist the bottom bolt, up to 15 blows in 5 seconds

In short, unfortunately, nothing helped me. Light, you didn't translate in vain, maybe someone else will come in handy. This is very useful information!

You are absolutely right! These are the features of my translation

Please tell me if I understood correctly that the upper screws and the lower one must be twisted in different directions to achieve the same result? That is, to accelerate the lower speeds, the upper screws must be unscrewed (counterclockwise), but at 6 speeds, the lower screw must, on the contrary, be screwed in. Did I understand correctly and precisely?




Yes, I understand. But I don't mind helping you. Moreover, the video is so sensible, and our Kitchen is so beautiful inside - it's just lovely!

Judging by the video - yes
from memory, when I tried to set it up, it looked like this
what's the point, initially the board is tilted, the speed switch, resting on the lower screw, closes the circuit and the mixer starts to work, the higher we set the speed, the further the lower part of this board pushes the switching speed, those, the board, becoming more perpendicular, increases the speed, as a result, the maximum speed when the bottom of the board is retracted by the switch further than the top

That is, by tightening the lower screw, you move the lower part of the board to a more perpendicular position, they increase the speed, by unscrewing the screw, the switch has to travel a greater distance in order to push the lower part of the board to the perpendicular, those speed is lower

Something like that

On Mon I'll pick up the parts and go to look for an electrician to put replacement parts on the board, then unsubscribe

On Mon I'll pick up the parts and go look for an electrician to put replacement parts on the board, then unsubscribe

Unsubscribe be sure!

[caprice23]

caprice23, Natasha, I'm sorry. But don't get mad at kitschen too much. You can find the details. Now e1win will set up your car and you follow him ... Here's how it happens, you wouldn't know if this question hadn't come up in the topic.

But don't be mad at kitschen too much

I'm not angry with him, he is so beloved! But I was very upset.

you would not have known if this question had not surfaced in the topic.

I am very grateful to e1win for bringing this up here. Hopefully my mixer can be repaired. The most annoying thing is that I don't understand anything in this electronics. I feel completely powerless.

I'm not angry with him, he is so beloved! But I was very upset. I am very grateful to e1win for bringing this up here. Hopefully my mixer can be repaired. The most annoying thing is that I don't understand anything in this electronics. I feel completely powerless.

Well, you don't need to hammer your head with this nonsense, it would be completely nonsense if the ladies ran around the shops for resistors and sat in the evenings with a soldering iron)

I tried to adjust the sixth speed with the lower screw. It seems like it reacts to unscrewing-screwing. I turned it stronger at 200 per minute, unscrewed it - 180. But the first one is not. 35-40 in 15 seconds.
And it is interesting that if the lower screw is unscrewed strongly, then all speeds up to the sixth become absolutely the same and increase only from the sixth. And if you twist more than half, then there is a difference between the first second third. Quite scanty, but there is. But it starts all the same with 35-37 rpm in 15 seconds.




Can someone tell me what's smart about this?

[caprice23]

caprice23, Natasha can pay attention to the top two screws with springs left and right. Of course, it’s impossible to even read a video where the credits jump quickly, I’m not even talking about the fact that it’s still a woman’s mind to understand in time. I propose to do the following: first, rewrite the entire text from the credits through frequent "stops" on paper - and then, with the expression and the learned text, record your voice with the text on an Audi recording on anything. And already looking at the video (turn down the sound in it) and at the same time listening to your audio recording with the text, you get synchronization. In this version, you will get a better assimilation of what you see. It's just that when the credits are read, it is impossible to see the actions on the video (and generally do not even have time to read it). But in synchronization with your voice, it will give you the opportunity not only to see and understand everything, but also to understand why exactly so. Look carefully with your eyes and listen with your ears at the same time and there will be a result. I ask you not to give up, but calmly and carefully and in detail and slowly study the video - it is not bad, the translation is not quite technical, as we are used to. And voice translation will definitely help you to correctly understand the subtleties of the settings. Patience and confidence: Everything is done by human hands and it is necessary to fix it by them.

[Sofita]

Sofita, Thank you. But Sveta translated for me on the previous page. So, in principle, everything is clear ... And e1win also wrote everything in great detail ...



I'll wait for what happens e1win... I hope his mixer will work correctly after repair and then I will follow in his footsteps

[caprice23]

caprice23, I have a feeling from the video that some small subtlety due to technical translation (not everyday) was missed and translated not very accurately, but the meaning is different.

maybe someone will be interested, in "Pyaterochka" an action has started with the participation of baking dishes "Kitchenaid". The promotion will run from October 1 to December 31.

🔗

[Svetlenki]

Svetlenki, I really liked the molds, but it is not clear how many stickers are needed and how much to pay extra, metal ones even look very decent, tomorrow I’ll go to exploration, next to 2 fives, I haven’t been there for a long time, I don’t really like them, I like the intersection more, it is even closer and until 1 pm 10% discount for senior citizens. But for the Kitchen's sake, I'm ready to visit the fives for a while.

[Sofita]

Sofita, if you click on the form on this site, then everything is written there - both the price and the number of stickers.

It seems to me that I had already read about such an action in Pyaterochka on the forum earlier. Does anyone have such forms? Are you satisfied?

metal even look very decent

Not at all in the subject, but very cool anodized aluminum for baking from Ikea (VARDAGEN collection). Here are just awesome. I don't know why I said it, but they are very good for a pastry chef.

[Anchic]

Anchic, Okay, I'll go poke now, I wonder what it will turn out to be, calculate how many times you have to go there to get stickers.



Svetlenki, although I have a lot of Nordics, but I also really want Kitchens, with good pastries to visit, that's the very thing, but about pastries, you can get more details, maybe I can do it too, but I don't know about it and what relates to it.



I went, looked and thought: one sticker - spend 300r, for iron Kitchen you need to collect 75 stickers. I liked 3 positions - and this is 75 multiplied by 3 = 225 stickers.
225 stickers multiplied by 300r = 67500r + the cost of the Kitchens themselves (599 + 299 + 299 = 1197r)
In total you will have to spend: 67500r + 1197 = 68697 rubles for one set and two molds - Cool! We need to think about who can share these precious stickers themselves (225pcs) In a task, so a task.

In Lithuania last year there was an action with stickers for Kitchen.
I also calculated the costs of these stickers yesterday. If you collect one item, the amount is comparable to spending on food per month for a family. But we have such a nasty pyaterochka store.
I only go into it out of great need. Yesterday I was for the first time in six months, I really needed bread, I went to the store without money, only with a phone, and where they sell delicious bread, only for cash. I had to get to the top five. There is no assortment, there is no queue at the checkout, the average check is 250 rubles (for some reason there was a queue from the marginals, they took beer, seeds and crackers)
There is not even a moving tape in front of the cash register, it is a pity for the cashiers, they move everything and stretch constantly.
In short, I'm past with a five

And we were generally cheated. Promotion only for Moscow, Moscow region and St. Petersburg ...

[Sofita]

Sofita, if I suddenly have stickers, I will be glad to share. But I very, very rarely go there. So it’s not worth counting too much. It will be possible to create Temko, as with knives. The girls shared stickers.

[e1win]

Eh, where is e1win I am waiting and worried. How are things going with the renovation?

Promotion only for Moscow, Moscow region and St. Petersburg ...

Today I saw a set of whisk-spatula from KitchenAid in "Pyaterochka". Not impressed at all by him. I didn't even take a picture, I didn't like it so much.