Dishwasher selection (1)

...
comrades, tell me how to insert forks and spoons? point up? because it is written in the instructions "with the tip DOWN", and then there is a picture - I think with the tip up, translation errors? the points can get through and lock the rocker arms, right?

My instructions say that spoons, forks - point up, knives - down. So I do it.
And here are my tea. spoons love to slip through the holes with their narrow ends, so I got used to putting them in the middle. stand compartment (it has a higher bottom than in 2 compartments on the sides, and there are fewer holes), and tea. my spoons stick out in height like the rest of the forks.

and I always thought that the middle compartment with a higher bottom is just for short items, such as teaspoons
just now I remembered that for a long time I tried to wash the labels from the cans in the dishwasher - and then accidentally put one such can in the micron - so the label went off perfectly without any traces - apparently, the glue burned out

and then accidentally put one such jar into the micra - so the label went off perfectly without any traces - apparently, the glue burned out

Was the jar filled with water or empty? I also hate labels on cans, I always suffer

And my PMM herself chooses how long to wash (6th sense) and sausage the unfortunate dishes for at least 2 hours and with a decent temperature, any labels come off. True, the glue is not all washed off, it’s too sticky.

empty
the fact of the matter is that now I don't understand why I put an empty jar in the microwave at all ...
Probably, initially there was a little water in it and I kind of wanted to sterilize it, but in the end ...
the first one was from Maccona coffee

the labels themselves, yes, they do, only then you need to pull out the pieces, but then I was amazed that in 1 minute the sticker itself came off, however, if the power is high, the glue may smell a little

we select a dishwasher for ourselves in all parameters and functions, the Bosch SRI 45M15 EU model is suitable, but there are no reviews about this model anywhere ... who uses or has used this please unsubscribe ... how can it please and what upset?

[polugal]

polugal, what did you like about this model?

to be honest ... the price ... half load ... and 3 in the 1st .... what's wrong with it?

I don't know about the price, half load in a 45-cm car is not needed IMHO, almost all Bosch models have 3 in 1
How much it costs? does the open panel bother you? have you seen her in real life? judging by decibels - noisy (52 versus 47)
I would look in the dishwasher for a beam on the floor, a fully built-in facade (but the convenience of such an installation is of course challenged), a shower head for washing pallets, an adjustable top box in height, minimal noise, a washing temperature of 70 degrees, the presence of any baubles-fasteners to keep small subjects

the price is 17-19 thousand rubles. half load is desirable for our family ... and why is the open panel bad? the course of the program before our eyes

In fact, the instructions for the PMM say that cans with labels cannot be washed ...

the price is 17-19 thousand rubles. half load is desirable for our family ... and why is the open panel bad? the course of the program before our eyes

I personally did not like the open panel in the interior of my kitchen - I took it without it
if you need to know how much time is left, you can always open the door and see
I still need half the load 5 times in 5 years - if this happens, I just put a rinse so that it does not dry out and then I report to a decent amount of dishes for washing
usually typed per day)))

the price is 17-19 thousand rubles. half load is desirable for our family ... and why is the open panel bad? the course of the program before our eyes

Newer models can be purchased for this price. I personally do not like the open panel, well, only if it was super beautiful and it would be pleasant to look at it, which the boshes clearly do not reach. Although the course of the program is very convenient in front of our eyes, but as a last resort, you can open the door and see what is happening there, plus a beam on the floor lets you know that the machine is working. I have 45 cm for two - I have never thought that how good it would be to have a half load, this simply does not happen. And the lack of reviews means that the model is not popular? After all, for a reason?

so what model to buy ... please offer something

I liked this narrow one, it has enough bells and whistles .. the top moves, at the bottom there is also something that folds for pots .. and the design fits my refrigerator
DeLonghi WMD31HI

I liked this narrow one, it has enough bells and whistles .. the top moves, at the bottom there is also something that folds for pots .. and the design fits my refrigerator
DeLonghi WMD31HI

what is the name of your car? what is her pedigree?

[polugal]

polugal, to the right of the photo below - the model is painted

[polugal]

Does anyone really use this DeLonghi WMD31HI? Most likely, the production is China, since everything that I saw from this company was all produced there. If you don’t have a lot of money (I don’t like it - I’ll buy another one), then you need to buy a proven model, it seems to me.
polugal, go to the Yandex market 🔗 on the right we look at the Most Desired:
Bosch SRV 55T13
Bosch SRV 55T34
BEKO DFS 6830
Zanussi ZDTS 300
Bosch SMV 63M00
We go to each model and read the reviews. Then we go to the store and really compare all the models (quality, convenience of baskets, or something else)
You can go to the forum 🔗 find the topic of choosing a dishwasher is not too lazy to read.
And advising specific models is also a responsible business, but what if you don't like it in the end? Who is guilty?
I would choose Bosch SRV 55T13 or Bosch SRV 55T34, read the reviews about them, and there are a lot of owners in this thread. I personally have a Bosch SRV 55T13, although I will not say that I am 100% satisfied directly. But this is my first machine, can not be compared with anything simple.
And if you still want an open model, then BOSCH SRI 55T25 EU is better than BOSCH SRI 45M15 EU, take a closer look.

Does anyone really use this DeLonghi WMD31HI? Most likely, the production is China, since everything that I saw from this company was all produced there.

No. Available on other models:
Delonghi WMD15 - 1 review 5 *
Delonghi WMD30I - 1 review 4 *
Delonghi WMD80I - 1 review 1 *
Delonghi WMD55 - 1 review 4 *
Delonghi WMD70HI - 2 reviews 1 *
Delonghi WMD60 - 1 review 2 *
Delonghi WMD20HI - 3 reviews 5 + 4 + 2 *

The overall picture is not great ... but the design of others for this amount did not find such doors of such handles

Help me choose a model, maybe someone uses it or knows something about these models, I will be grateful for the reviews of Beko DFN 5610 and BEKO DFN 6835

Help me choose a model, maybe someone uses it or knows something about these models, I will be grateful for the reviews of Beko DFN 5610 and BEKO DFN 6835

I have a BEKO DFN 6837 model, I bought it in April last year. If I am not mistaken, then the BEKO DFN 6835 model is the previous version of mine. Description of DFN 6837 is available here: 🔗
In the same place in the "Archive" submenu there was a list with the description of "obsolete" models. Now it is displayed empty for me: (Or an error on their website (it works crookedly), or with me with the Internet (it also happens)

I am a very machine !!! happy! She works for me at least once a day. It washes perfectly, provided that the dishes are arranged correctly (the instructions say in detail what and how to do). Roomy. Of all the inexpensive ones I looked at in stores (i.e., except for Bosch, etc.), at Veko, I liked the design of baskets most of all.
Sensitive to the voltage level in the network, but not critical: we just live in a place where the voltage jumps from 180 to almost 240 If it is low, it happened that the dishes were washed badly. Now the problem was solved with a stabilizer.

There were actually a lot of programs - I only use a shortened daily (1 hour, 65 degrees) or auto (almost 3 hours). Still rarely - for pots (2 hours with a tail, 70 degrees).

If in doubt, there was a Veko brand store in Podol, you can see and consult there. I really didn't get to them

Julchen is here for many girls of the century and if not lazy look in this thread a lot has been written about her. Here you can start with page 42. Answer 417 there Tortyzhka tells about his eyelid.In general, there are positive reviews about her.

Hello everyone in this thread! This is me again with my epic with the PMM. In general, the first round ended with the return of the car to the store, because they did not have the same at that time (the service recognized a factory defect in the current condensate tank), but were only in damaged packaging (i.e., IMHO, most likely not new and repaired). Almost two months have passed, I was honestly waiting for a new delivery. Finally they came !!! I ordered, received it - my Asko D5893 XL FI ... Examined with my husband ... well ... very biased! Visually, everything is fine, except that it is in dry drops (we attributed these traces to the fact that the cars are being checked, and now it’s summer - they could dry out). We connected it immediately - everything was as it should be according to the instructions. The car hums a little differently than the previous one, but nothing bothers you, and most importantly! this one does not flow !!! - already carried out about 20-30 washes - does not flow. But .......... Jeffrey !!!!!!!!!! For God's sake tell me, what is my problem with this car? !!!!! The problem came to light as follows: at some point, when 2-3-4-5 washing goes in a row, when the program is turned on, a horizontal strip of missing pixels goes across the entire display. This makes it difficult to read the name of the program. Moreover, if the car is cold, then this is not - and the husband suggested that the electronics are affected by the increased temperature (or maybe moisture gets there?) - this was not the case on the previous car. Moreover, this does not affect the operation of the machine - it washes the dishes normally, only this strip is annoying, and somehow, by inertia, I am afraid if this will affect later. It seems like a guarantee - 2 years, but ... And to be honest, I don't even know what to do with it and whether to do something? ... Jeffrey, ay !!!! I trust your opinion more than anyone else - tell me something, please !!!

[mish]

mish, You puzzled me ... In a typewriter for 1200 bucks, does this happen
It looks like a banal bad ration. After all, the service center is worth the strain.

But it happens! I don't know directly: again, what is the exchange of goods to make ?! What the hell is this! I still have a week to apply for an exchange - I will probably have to ...

[Jefry, mish]

Jefry, mish Any manufacturer has a marriage, no matter how banal it is very difficult to carry out a 100% performance check! Here the matter is apparently in a latent defect in the electronic unit, which, as you know, was made by subcontractors.
Urgently to the service, and (or) breaking the sales contract with a refund!
Second PMM with marriage, leads to sad reflections

[mish]

mish, very unpleasant .. I would have changed for another model .. I know a person whose laptop broke on the second day and was replaced with a new one - three times in a row! in the end I took a different model and for several years everything is ok .. (it was in Western Europe)

I called the service - there will be a master one of these days. The machine is running and still produces this strip of blank pixels. And once there - inside the electronic scoreboard (inside - because the outside was not rubbed off and moved a little when pressed) there was a tiny drop of water. At the next wash, it evaporated somewhere. How to convey this to the master - I don't know - will they take their word for it.
sazalexter, you are right - I also worry that the second PMM is from the same store, and like that, but they have different problems: in the first case - a condensate tank, in the second - electronics. I think Jeffrey is right that there is something wrong with the soldering - which is sad. You don't want to give up this model - only it allows you to change the washing parameters as you like and set the required temperature in any program. I walked to this car for a year or a year and a half. By the way, I'm not superstitious, but you can't believe it .... the numbers of both orders ended with "13".

[mish]

mish Maybe look for something similar from Miele or AEG?

sazalexter, I was looking! But AEG has no analogues, while Miele's price goes off scale one and a half to two times - and this is beyond me ...

... And once there - inside the electronic scoreboard (inside - because the outside was not rubbed off and moved a little when pressed) there was a tiny drop of water. At the next wash, it evaporated somewhere.How to convey this to the master - I don't know - will they take their word for it.

A drop of water is a much more wake-up call than the missing pixel line. And you need the master to figure out how she got there! If you can still use a typewriter with a poor contact in the display (although there is also a possibility that it is poorly sealed somewhere in a more important place), then the moisture in the electronics unit will sooner or later be made by the "ax".

The master came. Before his arrival, I drove the car for a long time so that it was hot when a streak appeared. The stripe appeared and disappeared, and I was already getting nervous that at the most crucial moment I would have nothing to show the master: well, she would not appear and that was all! A friend advised me to take a picture of this strip - I did so, but it was not required - the strip was there by the time the master arrived. He unscrewed the car, looked over to where the board was - I don't know what he saw there, said that he would just write a service form and let them change the car. In the form he wrote that it was necessary to change the display (he said that let them figure it out - the display is naughty or a fee) and that the client refused to repair, therefore the exchange of goods or the return of funds. I just sent an application with a service report to the store. Now I'm waiting for an answer.

Hello! the other day I became the owner of a dishwasher, dreamed about it for many years and finally! I bought a whirlpool ADG175 installation and for some reason it upsets me to the noise and quality of the washing, there are no pritenzy, but after each use at the bottom of the car, a pile of water, right up to the door, scooped out a basin and a half came out. Is it normal? can connect what is wrong?
And another question for the owners of the whirlpool how to determine whether she has finished the program or not, except for the noise and squeak? I turned it on, the lights blinked for a minute and turned off, only the one near the power button remained on, there is a display but nothing is displayed on it. chose chose chose pancake (((

[Madam]

but after each use at the bottom of the car, a pile of water, right up to the door, scooped out a bowl and a half came out. Is it normal? can connect what is wrong?

Madam!
Specify the distance between the inlet to the drain and the outlet from the dishwasher. In centimeters or millimeters.

[Madam]

Madam!
Specify the distance between the inlet to the drain and the outlet from the dishwasher. In centimeters or millimeters.

about two meters, not standing nearby, lengthened. the hoses are lying on the floor. wrong yes?

You need no more than 2 meters !!!! I think this is the problem !!!

[madama]

Usually they write no more than four meters. But here is another case, on ixbt the question was asked in a more detailed way and the answer suggests itself. Or there is something wrong with the indication of the operating mode, but madama does not see whether the program has ended or not and opens the machine during drying.

yeah, it turned out that I climbed during the drying, it turns out in this car, except for a squeak, there is no indication of the end of the program, put it on for the night, opened everything ok in the morning, there is no water. this is my first machine and therefore panic.

Again I ask for advice from my favorite forum
You need a fully built-in dishwasher 45 cm, AAA, preferably a budget one, but rather functional. What to look for? what do you need in PMM? In about the same price category, Whirlpool, Ariston, Beko, Zanussi. Which brand should you prefer? what features are required? Sorry for stupid questions, but I already don't understand anything from the amount of the choice

Well, now I'm really afraid to answer stupidly. When we bought our Beko 5830, the instructions said that the top cover can be removed and it can be "built in". Now I went to 5ok, there are 6830. The girls praised this model. Take a closer look: 🔗

Look here, a very good model, with all the necessary functions1 !!
🔗

Well, now I'm really afraid to answer stupidly. When we bought our Beko 5830, the instructions said that the top cover can be removed and it can be "built in". Now I went to 5ok, there are 6830. The girls praised this model. Take a closer look: 🔗

In terms of functions, the model, but I need a fully built-in one - so that the front panel can be closed with the furniture facade and nothing can be seen.Free-standing can be shoved under the countertop, but you cannot hang the facade in front
And only Beko DIS 5830 is fully built-in, there are fewer functions - so I choose

Look here, a very good model, with all the necessary functions1 !!
🔗

I agree, the machine is super, only the price would be 150-200 ye less

[Jefry]

Jefry, is that you? Is the review positive?
I looked at it, but the freestanding 6830 has better functions, so it confuses how the 5830 will be .. It is also embarrassing that for the same price there are options such as European manufacturers .. can it be better to take them? or not to fall for public opinion about Turkish technology?

[Jefry]

Jefry, is that you? Is the review positive?
I looked at it, but the freestanding 6830 has better functions, so it confuses how the 5830 will be .. It is also embarrassing that for the same price there are options such as European manufacturers .. can it be better to take them? or not to fall for public opinion about Turkish technology?

I have a Chinese typewriter Hayer, a positive review! The number of functions is the case, in the end we use one or two ...

Well! Also some kind of Hayer drew - I have not heard of such

I have this:
_https: //Mcooker-enn.tomathouse.com/s-image/2632/HAIER-DW9-CBE7.htm
They are no longer on sale anywhere and the authorized service suddenly disappeared ... But personally, I don't have to worry about this

Well! Also some kind of Hayer drew - I have not heard of such

we have good reviews on hayer.
This Haier DW12BFE and this Haier DW15PFE2ME

More owners of built-in dishwashers go plz

So far I stopped at WHIRLPOOL ADG 789. How do you like it?

Nice car !!! Convenient basket both top and bottom. Apparently Turkey does approximately the same: D I have a Veko-I am sooooo happy with it !!!